Related references
Note: Only part of the references are listed.Microstructure and mechanical properties in the TLP joint of FeCoNiTiAl and Inconel 718 alloys using BNi2 filler
Lin Yuan et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)
Insight into Si poisoning on grain refinement of Al-Si/Al-5Ti-B system
Yang Li et al.
ACTA MATERIALIA (2020)
The effects of Cr addition on microstructure, hardness and tensile properties of as-cast Al-3.8wt.%Cu-(Cr) alloys
Thiago M. Ribeiro et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)
Effect of scandium addition on microstructure and mechanical properties of as-cast Al-5%Cu alloys
Qinglin Li et al.
VACUUM (2020)
Effects of AlCoCrFeNiTi high-entropy alloy on microstructure and mechanical properties of pure aluminum
Qinglin Li et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)
Enhanced age-hardening behavior in Al-Cu alloys induced by in-situ synthesized TiC nanoparticles
Huabing Yang et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)
Elasto-plastic deformation in Al-Cu cast alloys for engine components
M. Schoebel et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2019)
Influence of the modification of iron-bearing intermetallic and eutectic Si on the mechanical behavior near the solidus temperature in Al-Si-Cu 319 cast alloy
Kun Liu et al.
PHYSICA B-CONDENSED MATTER (2019)
A novel modifier on the microstructure and mechanical properties of Al-7Si alloys
Qinglin Li et al.
MATERIALS LETTERS (2019)
Microstructure and properties of as-cast Al-4.5Cu-1.5Mg alloy refined with Ti-supported TiC nanoparticles via ultrasonic-assisted addition
Bingyi Zhao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
An experimental investigation of phase transformations in the Al-rich corner of the Al-Cr-Fe system
D. Ezemenaka et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2019)
In situ nanotomography study of creep cavities in Al-3.6-Cu alloy
R. Kumar et al.
ACTA MATERIALIA (2019)
Co-stabilization of θ′-Al2Cu and Al3Sc precipitates in Sc-microalloyed Al-Cu alloy with enhanced creep resistance
Y. H. Gao et al.
MATERIALS TODAY NANO (2019)
On the preparation and mechanical properties of in situ small-sized TiB2/Al-4.5Cu composites via ultrasound assisted RD method
Jun Liu et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2018)
Analyzing the microstructural evolution and hardening response of an Al-Si-Mg casting alloy with Cr addition
Hongyi Zhan et al.
MATERIALS CHARACTERIZATION (2018)
The mechanistic contribution of nanosized Al3Fe phase on the mechanical properties of Al-Fe alloy
X. Wang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Grain size-dependent Sc microalloying effect on the yield strength-pitting corrosion correlation in Al-Cu alloys
S. H. Wu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Simultaneously increasing the high-temperature tensile strength and ductility of nano-sized TiCp reinforced Al-Cu matrix composites
Wei-Si Tian et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Effect of semi-solid forging on microstructure and mechanical properties of in-situ cast Al-Cu-TiB2 composites
James Mathew et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2017)
Grain refinement of binary Al-Si, Al-Cu and Al-Ni alloys by ultrasonication
N. Srivastava et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Superior creep resistance of 0.3 wt% nano-sized TiCp/Al-Cu composite
Wei-Si Tian et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Mechanical properties and optimization of the aging of a dilute Al-Sc-Er-Zr-Si alloy with a high Zr/Sc ratio
Anthony De Luca et al.
ACTA MATERIALIA (2016)
Strengthening mechanisms in an Al-Fe-Cr-Ti nano-quasicrystalline alloy and composites
S. Pedrazzini et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
Mechanical properties enhanced by deformation-modified precipitation of θ′-phase approximants in an Al-Cu alloy
P. P. Ma et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
Effect of homogenisation treatment on precipitation, recrystallisation and properties of Al-3% Mg - TM alloys (TM = Mn, Cr, Zr)
A. V. Mikhaylovskaya et al.
MATERIALS & DESIGN (2016)
Effect of Cr content and heat-treatment on the high temperature strength of eutectic Al-Si alloys
Yuying Yang et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2015)
Grain refinement behavior of Al-Cu alloys inoculated by various metallic glasses
Zhihao Bai et al.
MATERIALS CHEMISTRY AND PHYSICS (2015)
Length-scale dependent microalloying effects on precipitation behaviors and mechanical properties of Al-Cu alloys with minor Sc addition
L. Jiang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)
Microstructure and crystal growth direction of Al-Cu alloy
Ti-jun Chen et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2015)
Prediction models for the yield strength of particle-reinforced unimodal pure magnesium (Mg) metal matrix nanocomposites (MMNCs)
Chang-Soo Kim et al.
JOURNAL OF MATERIALS SCIENCE (2013)
Effect of fine-grained raw material addition on microstructure refinement and tensile properties in horizontal continuous casting Al-12%Si alloy billets
Jing Zhang et al.
MATERIALS & DESIGN (2011)
An analytical model for constitutional supercooling-driven grain formation and grain size prediction
M. Qian et al.
ACTA MATERIALIA (2010)
A model of grain refinement incorporating alloy constitution and potency of heterogeneous nucleant particles
MA Easton et al.
ACTA MATERIALIA (2001)
Share Paper
