☆ 4.7 Article

Modelling of Springback in Tube Bending: A Generalized Analytical Approach

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2021)

Related references

Note: Only part of the references are listed.

Article Engineering, Industrial

Loading conditions constrained wrinkling behaviors of thin-walled sheet/tube parts during metal forming

Heng Li et al.

Summary: This study investigated the wrinkling instability of thin-walled parts forming under different loading conditions, finding that wrinkling is more prone to occur under tension-compression stress state, and processes without normal constraints exhibit more severe wrinkling. The effects of material parameters on wrinkling are inconsistent in different processes, with the degree of normal constraint impacting the influence of material properties. By combining geometric and material parameters, key issues affecting wrinkling behavior have been elucidated, providing a foundation for further study.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

Add to Collection

Article Engineering, Industrial

Nonlinear anelastic behavior and unloading-reloading constitutive models of severe plastic compressive deformation

Hongli Hou et al.

Summary: The study focused on the nonlinear anelastic behavior in unloading and unloading-reloading processes of severe plastic compressive deformation (SPCD) in hot-rolled copper plates along different directions. Experimental tests were conducted to analyze the unloading behavior, variation law of anelastic strain, and the effect of anisotropy. Models were established at micro and macro levels to accurately predict the anelastic strain and stress-strain relationship in SPCD.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

Add to Collection

Article Mechanics

Effect of tension-compression asymmetry of AZ31B magnesium alloys on four-point bending

Emile Roux et al.

Summary: The mechanical response of magnesium alloy AZ31B under tension-compression loading was studied using four-point bending tests, and the evolution of strain fields during the test was measured with digital image correlation. The results showed that the neutral line of the specimen initially shifted towards the tensile side and then back towards the center, causing some physical points of the specimen to alternate between compression and tension, but these alternations were limited to the elastic domain.

MECHANICS RESEARCH COMMUNICATIONS (2021)

Add to Collection

Review Chemistry, Physical

Advances and Trends in Forming Curved Extrusion Profiles

Wenbin Zhou et al.

Summary: Curved profiles have been widely used in high-technology industries due to their lightweight, high strength, and superior aerodynamics performance. This paper reviews the advances and trends in forming techniques of curved extrusion profiles of metal alloys, with a focus on the potential for further innovation in the extrusion-bending integrated technique.

MATERIALS (2021)

Add to Collection

Article Engineering, Manufacturing

Insights on tube rotary draw bending with superimposed localized thermal field

Andrea Ghiotti et al.

Summary: Manufacturing hollow section profiles using high strength metallic alloys may face drawbacks such as springback, reduced formability, and wrinkling, which can be significantly reduced by localized heating. An analytical approach is proposed in the paper to predict stress and strain distributions in the cross-section and their impact on springback, with experimental and numerical validations confirming the model's reliability.

CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2021)

Add to Collection

Article Engineering, Manufacturing

Breaking bending limit of difficult-to-form titanium tubes by differential heating-based reconstruction of neutral layer shifting

Heng Yang et al.

Summary: Utilizing differential heating to achieve small-radius bending of difficult-to-form tubular materials by proactively coordinating non-uniform deformation and preventing multiple forming defects to break the bending limit is a promising approach. The method has been shown to expand the design and optimization space for neutral layer shifting reconstruction in tube bending, increase work hardening of titanium tubes, and reduce wall-thinning and cross-section flattening.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2021)

Add to Collection

Article Engineering, Manufacturing

The impact of thermo-mechanical processing routes on product quality in integrated aluminium tube bending process

J. Ma et al.

Summary: This research investigates the impact of thermo-mechanical processing routes on the quality of heat-treatable aluminum tubes in integrated bending processes. The study finds that routes involving bending after solution-heat-treatment can significantly reduce springback and wall-thinning, while naturally-aged tubes may affect the mechanical properties of the products. Moreover, routes with artificial aging can achieve more uniform hardness distribution in the cross-section of bent tubes.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Engineering, Mechanical

Modeling of 3D plastic anisotropy and asymmetry of extruded magnesium alloy and its applications in three-point bending

Fei-Fan Li et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2020)

Add to Collection

Article Nuclear Science & Technology

Analytic springback prediction in cylindrical tube bending for helical tube steam generator

Kwanghyun Ahn et al.

NUCLEAR ENGINEERING AND TECHNOLOGY (2020)

Add to Collection

Article Engineering, Mechanical

Temperature dependent evolution of anisotropy and asymmetry of α-Ti in thermomechanical working: Characterization and modeling

H. Yang et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2020)

Add to Collection

Article Automation & Control Systems

Springback prediction of AL6061 pipe in free bending process based on finite element and analytic methods

Yusen Li et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

Add to Collection

Article Engineering, Mechanical

Theoretical modelling and finite element simulation of AA6061 involute components based on 3D free bending process

Tao Li et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2020)

Add to Collection

Article Mechanics

Plastic bending of sheet metal with tension/compression asymmetry

Kanghwan Ahn

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2020)

Add to Collection

Article Automation & Control Systems

Push-bending method development of thin-walled tube with relative bending radius of 1 using sectional elastomers as mandrel

Xuefeng Xu et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)

Add to Collection

Article Engineering, Mechanical

An analytical springback model for bending of welded tube considering the weld characteristics

M. Zhan et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2019)

Add to Collection

Article Engineering, Industrial

Flexibility in metal forming

D. Y. Yang et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Automation & Control Systems

Tribological behaviors in titanium sheet and tube forming at elevated temperatures: evaluation and modeling

J. Ma et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Engineering, Manufacturing

An insight into neutral layer shifting in tube bending

H. Li et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2018)

Add to Collection

Article Engineering, Mechanical

Springback study of RDB of rectangular H96 tube

Y. X. Zhu et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2018)

Add to Collection

Article Engineering, Mechanical

Modelling of hot rotary draw bending for thin-walled titanium alloy tubes

Enrico Simonetto et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2018)

Add to Collection

Article Engineering, Industrial

Mechanics of the reciprocal effects of bending and torsion during 3D bending of profiles

Daniel Staupendah et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)

Add to Collection

Article Engineering, Mechanical

A method for investigating the springback behavior of 3D tubes

Jianjun. Wu et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2017)

Add to Collection

Article Engineering, Mechanical

Strength differential effect in age hardened aluminum alloys

Jens Kristian Holmen et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2017)

Add to Collection

Proceedings Paper Engineering, Multidisciplinary

Springback Behavior of AA6082T6 Tubes in Three-point Bending Operation

Mehmet Alper Sofuoglu et al.

7TH INTERNATIONAL CONFERENCE ON ENGINEERING, PROJECT, AND PRODUCTION MANAGEMENT (2017)

Add to Collection

Article Engineering, Industrial

Closed-loop control of product properties in metal forming

J. M. Allwood et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2016)

Add to Collection

Article Engineering, Industrial

An analytic model for tube bending springback considering different parameter variations of Ti-alloy tubes

Mei Zhan et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)

Add to Collection

Article Engineering, Industrial

Variation and consistency of Young's modulus in steel

Zhong Chen et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)

Add to Collection

Proceedings Paper Physics, Applied

Springback prediction of titanium tube bending considering Bauschinger effect and Young's modulus variation

J. Ma et al.

NUMISHEET 2016: 10TH INTERNATIONAL CONFERENCE AND WORKSHOP ON NUMERICAL SIMULATION OF 3D SHEET METAL FORMING PROCESSES, PTS A AND B (2016)

Add to Collection

Article Engineering, Industrial

Springback analysis of Z & T-section 2196-T8511 and 2099-T83 Al-Li alloys extrusions in displacement controlled cold stretch bending

Tianjiao Liu et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Investigation of Neutral Axis Shifting in Rotary Draw Bending Processes for Tubes

Bernd Engel et al.

STEEL RESEARCH INTERNATIONAL (2014)

Add to Collection

Article Engineering, Mechanical

Advanced Issues in springback

Robert H. Wagoner et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of Additional Tensile Force on Springback of Tube Under Rotary Draw Bending

Daxin E et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2012)

Add to Collection

Article Engineering, Industrial

Springback characterization and behaviors of high-strength Ti-3Al-2.5V tube in cold rotary draw bending

H. Li et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2012)

Add to Collection

Article Engineering, Mechanical

Complex unloading behavior: Nature of the deformation and its consistent constitutive representation

Li Sun et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2011)

Add to Collection

Proceedings Paper Engineering, Multidisciplinary

Springback Control in Industrial Bending Operations: Assessing the Accuracy of Three Commercial FEA Codes

Torgeir Welo et al.

14TH INTERNATIONAL CONFERENCE ON MATERIAL FORMING ESAFORM, 2011 PROCEEDINGS (2011)

Add to Collection

Article Metallurgy & Metallurgical Engineering

A new adaptive bending method using closed loop feedback control

T. Welo et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2010)

Add to Collection

Article Engineering, Mechanical

Analytical springback model for lightweight hexagonal close-packed sheet metal

M. G. Lee et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2009)

Add to Collection

Article Engineering, Industrial

Bending of tube and section made of strain-hardening materials

A. El Megharbel et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)

Add to Collection

Article Materials Science, Multidisciplinary

Spring-back and residual stresses in bending of thin-walled aluminium tubes

HA Al-Qureshi et al.

MATERIALS & DESIGN (2002)

Add to Collection

Article Engineering, Mechanical

A model of large-strain cyclic plasticity describing the Bauschinger effect and workhardening stagnation

F Yoshida et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2002)

Add to Collection

Article Engineering, Multidisciplinary

Plastic-deformation analysis in tube bending

NC Tang

INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.