Related references
Note: Only part of the references are listed.Study of the evolution of transport properties induced by additive processing sand mold using X-ray computed tomography
Saptarshee Mitra et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)
Effect of process parameters on flexure strength and gas permeability of 3D printed sand molds
Tharmalingam Sivarupan et al.
JOURNAL OF MANUFACTURING PROCESSES (2020)
Rice Husk Waste as an Exothermic Material for a Riser Sleeve for Steel Casting
Dewi Idamayanti et al.
INTERNATIONAL JOURNAL OF TECHNOLOGY (2020)
Re-Thinking Design Methodology for Castings: 3D Sand-Printing and Topology Optimization
Jiayi Wang et al.
INTERNATIONAL JOURNAL OF METALCASTING (2019)
On the rapid manufacturing process of functional 3D printed sand molds
Saptarshee Mitra et al.
JOURNAL OF MANUFACTURING PROCESSES (2019)
Characterisation of 3D printed sand moulds using micro-focus X-ray computed tomography
Tharmalingam Sivarupan et al.
RAPID PROTOTYPING JOURNAL (2019)
Novel sprue designs in metal casting via 3D sand-printing
Santosh Reddy Sama et al.
ADDITIVE MANUFACTURING (2019)
Investigation of process parameter effect on anisotropic properties of 3D printed sand molds
Nicolas Coniglio et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
The effect of ageing process on three-point bending strength and permeability of 3D printed sand molds
Saptarshee Mitra et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
The Design of 3D-Printed Lattice-Reinforced Thickness-Varying Shell Molds for Castings
Haolong Shangguan et al.
MATERIALS (2018)
Non-conventional mold design for metal casting using 3D sand-printing
Santosh Reddy Sama et al.
JOURNAL OF MANUFACTURING PROCESSES (2018)
Effects of Changing Size-Weight Parameters on the Temperature Dependent Exothermic Riser Sleeve Properties
O. Yucel et al.
EURASIAN CHEMICO-TECHNOLOGICAL JOURNAL (2018)
Effect of printing speed on quality of printed parts in Binder Jetting Process
Hadi Miyanaji et al.
ADDITIVE MANUFACTURING (2018)
Additive manufacturing-driven mold design for castings
Jinwu Kang et al.
ADDITIVE MANUFACTURING (2018)
3D-printed shell-truss sand mold for aluminum castings
Haolong Shangguan et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
3D printing for rapid sand casting-A review
Meet Upadhyay et al.
JOURNAL OF MANUFACTURING PROCESSES (2017)
Effects of vibration frequency on microstructure, mechanical properties, and fracture behavior of A356 aluminum alloy obtained by expendable pattern shell casting
Wenming Jiang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
Effect of molding parameters on chemically bonded sand mold properties
Himanshu Khandelwal et al.
JOURNAL OF MANUFACTURING PROCESSES (2016)
Lightweight Metal Cellular Structures Fabricated via 3D Printing of Sand Cast Molds
Dean Snelling et al.
ADVANCED ENGINEERING MATERIALS (2015)
Influence of pouring temperature on solidification behavior, microstructure and mechanical properties of sand-cast Mg-10Gd-3Y-0.4Zr alloy
Song Pang et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2015)
Combined effects of mechanical vibration and wall thickness on microstructure and mechanical properties of A356 aluminum alloy produced by expendable pattern shell casting
Wenming Jiang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
The effect of section size on cooling rate, microstructure and mechanical properties of A356 aluminium alloy in casting
K. T. Akhil et al.
INTERNATIONAL CONFERENCE ON ADVANCES IN MANUFACTURING AND MATERIALS ENGINEERING (ICAMME 2014) (2014)
Correlation of microstructure with mechanical properties and fracture behavior of A356-T6 aluminum alloy fabricated by expendable pattern shell casting with vacuum and low-pressure, gravity casting and lost foam casting
Wenming Jiang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
Development of a substitute for Z cast molding sand used on installations of 3D printing for obtaining aluminum, magnesium, and iron casting
A. V. Koltygin et al.
RUSSIAN JOURNAL OF NON-FERROUS METALS (2012)
Effects of layer thickness and binder saturation level parameters on 3D printing process
Mohammad Vaezi et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2011)
Efficacy of powder-based three-dimensional printing (3DP) technologies for rapid casting of light alloys
Simranpreet Singh Gill et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2011)
FE prediction of residual stresses of investment casting in a Bottom Core Vane under equiaxed cooling
S.M. Afazov et al.
Journal of Manufacturing Processes (2010)
A novel technique for reducing macrosegregation in heavy steel ingots
Baoguang Sang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
The Al-Si Phase Diagram
George F. Vander Voort et al.
MICROSCOPY AND MICROANALYSIS (2009)
An Investigation into the Effective Heat Transfer Coefficient in the Casting of Aluminum in a Green-Sand Mold
Hsien-Chi Sun et al.
MATERIALS TRANSACTIONS (2009)
Interlamellar spacing and average interface undercooling of irregular eutectic in steady-state growth
Meng Guang-hui et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2008)
Interflake spacings and undercoolings in Al-Si irregular eutectic alloy
M Gündüz et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2004)
Share Paper
