Related references
Note: Only part of the references are listed.The crack healing effect of scandium in aluminum alloys during laser additive manufacturing
N. Qbau et al.
JOURNAL OF MANUFACTURING PROCESSES (2020)
Process-Dependent Composition, Microstructure, and Printability of Al-Zn-Mg and Al-Zn-Mg-Sc-Zr Alloys Manufactured by Laser Powder Bed Fusion
Le Zhou et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2020)
Understanding the Laser Powder Bed Fusion of AlSi10Mg Alloy
Holden Hyer et al.
METALLOGRAPHY MICROSTRUCTURE AND ANALYSIS (2020)
Microstructure of selective laser melted AlSi10Mg alloy
Xihe Liu et al.
MATERIALS & DESIGN (2019)
Microstructure and tensile property of a novel AlZnMgScZr alloy additively manufactured by gas atomization and laser powder bed fusion
Le Zhou et al.
SCRIPTA MATERIALIA (2019)
Microstructure, precipitates and hardness of selectively laser melted AlSi10Mg alloy before and after heat treatment
Le Zhou et al.
MATERIALS CHARACTERIZATION (2018)
Effect of scanning strategies on residual stress and mechanical properties of Selective Laser Melted Ti6Al4V
Haider Ali et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Effect of silicon content on densification, mechanical and thermal properties of Al-xSi binary alloys fabricated using selective laser melting
Takahiro Kimura et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
In-situ residual stress reduction, martensitic decomposition and mechanical properties enhancement through high temperature powder bed pre-heating of Selective Laser Melted Ti6Al4V
Haider Ali et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
The effect of preheating on microstructure and mechanical properties of laser solid forming IN-738LC alloy
Jianjun Xu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Formation of the Ni3Nb δ-Phase in Stress-Relieved Inconel 625 Produced via Laser Powder-Bed Fusion Additive Manufacturing
Eric A. Lass et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2017)
3D printing of high-strength aluminium alloys
John H. Martin et al.
NATURE (2017)
Additive manufacturing of metals
Dirk Herzog et al.
ACTA MATERIALIA (2016)
The metallurgy and processing science of metal additive manufacturing
W. J. Sames et al.
INTERNATIONAL MATERIALS REVIEWS (2016)
Rapid Solidification: Selective Laser Melting of AlSi10Mg
Ming Tang et al.
JOM (2016)
Effect of diffusion on susceptibility to cracking during solidification
Jiangwei Liu et al.
ACTA MATERIALIA (2015)
A criterion for cracking during solidification
Sindo Kou
ACTA MATERIALIA (2015)
Laser powder bed fusion additive manufacturing of metals; physics, computational, and materials challenges
W. E. King et al.
APPLIED PHYSICS REVIEWS (2015)
Review of selective laser melting: Materials and applications
C. Y. Yap et al.
APPLIED PHYSICS REVIEWS (2015)
Microstructure and mechanical properties of Al-12Si produced by selective laser melting: Effect of heat treatment
K. G. Prashanth et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
An A Priori Hot-Tearing Indicator Applied to Die-Cast Magnesium-Rare Earth Alloys
Mark A. Easton et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2014)
Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): Microstructure, high cycle fatigue, and fracture behavior
Erhard Brandl et al.
MATERIALS & DESIGN (2012)
Mechanisms for Solidification Crack Initiation and Growth in Aluminum Welding
N. Coniglio et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2009)
Process maps for predicting residual stress and melt pool size in the laser-based fabrication of thin-walled structures
Aditad Vasinonta et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2007)
Diffusion coefficients of some solutes in fcc and liquid Al: critical evaluation and correlation
Y Du et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)
Hot tearing of nickel-based superalloys during directional solidification
J Zhang et al.
ACTA MATERIALIA (2002)
Share Paper
