Related references
Note: Only part of the references are listed.Effect of various phase fraction of bainite, intercritical ferrite, retained austenite and pearlite on the corrosion behavior of multiphase steels
Neetu et al.
CORROSION SCIENCE (2021)
Enhanced plasticity of austempered ductile iron (ADI) by partitioning treatment
Xin Wang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)
A review: phase transformation and wear mechanisms of single-step and dual-step austempered ductile irons
Bingxu Wang et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)
Grain size refinement and effect on the tensile properties of a novel low-cost stainless steel
Yang Su et al.
MATERIALS LETTERS (2020)
Microstructural and mechanical properties of Cu-Ni-Mn-Mo austempered ductile iron obtained from two-step hot air austempering
Leonardo Pereira et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)
Tribological behavior of shot peened/austempered AISI 5160 steel
Xue Han et al.
TRIBOLOGY INTERNATIONAL (2020)
Microstructure evolution and wear resistance of high silicon bainitic steel after austempering
Zhang Changle et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)
Micro-pitting and wear characterization for different rolling bearing steels: Effect of hardness and heat treatments
Aleks Vrcek et al.
WEAR (2020)
Tribological behavior of austempered ductile iron (ADI) obtained at different austempering temperatures
Yuzhou Du et al.
WEAR (2020)
Microstructure, wear behavior and surface hardening of austempered ductile iron
Bingxu Wang et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)
Phase transformation mechanisms during Quenching and Partitioning of a ductile cast iron
Arthur S. Nishikawa et al.
ACTA MATERIALIA (2019)
Abrasive wear behavior of austempered ductile iron with niobium additions
Amanda Souza Oliveira Pimentel et al.
WEAR (2019)
Extremely high strength achievement in medium-C nanobainite steel
J. Zhao et al.
SCRIPTA MATERIALIA (2018)
Influence of intercritical austempering on the microstructure and mechanical properties of austempered ductile cast iron (ADI)
Saranya Panneerselvam et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Effect of hardness, microstructure, normal load and abrasive size on friction and on wear behaviour of 35NCD16 steel
Celine Trevisiol et al.
WEAR (2017)
Morphology and Crystallography of Ausferrite in Austempered Ductile Iron
Chengduo Wang et al.
METALS (2017)
Improvement in Abrasion Wear Resistance and Microstructural Changes with Deep Cryogenic Treatment of Austempered Ductile Cast Iron (ADI)
Sanja Solic et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2016)
Enhanced strain hardening capacity in a lean alloy steel treated by a disturbed bainitic austempering process
Guhui Gao et al.
ACTA MATERIALIA (2015)
Investigation of skidding in angular contact ball bearings under high speed
Yunlong Wang et al.
TRIBOLOGY INTERNATIONAL (2015)
Influence of carbon content on the microstructure, martensitic transformation and mechanical properties in austenite/epsilon-martensite dual-phase Fe-Mn-C steels
Jae-Bok Seol et al.
ACTA MATERIALIA (2013)
The effect of morphology on the stability of retained austenite in a quenched and partitioned steel
X. C. Xiong et al.
SCRIPTA MATERIALIA (2013)
Relations between roughness, temperature and dry sliding friction at the atomic scale
Peter Spijker et al.
TRIBOLOGY INTERNATIONAL (2013)
The production of high-density hollow cast-iron bars by vertically continuous casting
Guojun Yan et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2012)
Steels for bearings
H. K. D. H. Bhadeshia
PROGRESS IN MATERIALS SCIENCE (2012)
Influence of chemical composition and holding time on austenite (γ) → ferrite (α) transformation in ductile iron occurring within the intercritical interval
A. Basso et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2011)
Wear resistance of a bearing steel processed by laser surface remelting cooled by water
Peng-yu Lin et al.
SCRIPTA MATERIALIA (2010)
Grain size effect on wear resistance of a nanostructured AISI52100 steel
L. Zhou et al.
SCRIPTA MATERIALIA (2008)
Design of carbide-free low-temperature ultra high strength bainitic steels
Carlos Garcia-Mateo et al.
INTERNATIONAL JOURNAL OF MATERIALS RESEARCH (2007)
Ultra-fine bainite structure in hypo-eutectoid steels
Mohamed Soliman et al.
ISIJ INTERNATIONAL (2007)
Un-lubricated sliding wear performance of unalloyed austempered ductile iron under high contact stresses
J Zimba et al.
MATERIALS & DESIGN (2004)
Improvement of wear and hardness of steel by nitrogen implantation
AA Youssef et al.
VACUUM (2004)
Very strong bainite
FG Caballero et al.
CURRENT OPINION IN SOLID STATE & MATERIALS SCIENCE (2004)
Development of austempered ductile cast iron (ADI) with simultaneous high yield strength and fracture toughness by a novel two-step austempering process
SK Putatunda
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2001)
Tribological behaviour of quenched and tempered, and austempered ductile iron at the same hardness level
ASMA Haseeb et al.
WEAR (2000)
Share Paper
