Related references
Note: Only part of the references are listed.Finite element modeling of non-conventional energy dissipating systems using metallic like-composite tubular structures
H. S. Habte et al.
INTERNATIONAL JOURNAL OF IMPACT ENGINEERING (2020)
Microstructure, forming limit diagram, and strain distribution of pre-strained DP-IF steel tailor-welded blank for auto body application
Shamik Basak et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Determination of Strain Rate Sensitivity of Micro-struts Manufactured Using the Selective Laser Melting Method
Recep Gumruk et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2018)
Transition of failure mode in hot stamping of AA6082 tailor welded blanks
Jun Liu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)
A study of development mode of collapse with variation of strains and stresses during compression of metallic shells having dome-cone shape
P. K. Gupta et al.
THIN-WALLED STRUCTURES (2018)
On the crashworthiness performance of thin-walled energy absorbers: Recent advances and future developments
Ahmad Baroutaji et al.
THIN-WALLED STRUCTURES (2017)
Dynamic axial crashing of tailor-welded blanks (TWBs) thin-walled structures with top-hat shaped section
Fengxiang Xu et al.
ADVANCES IN ENGINEERING SOFTWARE (2016)
Sensitivity analysis and reliability based design optimization for high-strength steel tailor welded thin-walled structures under crashworthiness
Xueguan Song et al.
THIN-WALLED STRUCTURES (2016)
An advanced technological lightweighted solution for a Body in White
Elena Cischino et al.
TRANSPORT RESEARCH ARENA TRA2016 (2016)
Limiting drawing ratio and deep drawing behavior of dual phase steel tailor welded blanks: FE simulation and experimental validation
K. Bandyopadhyay et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)
Crushing and energy absorption characteristics of combined geometry shells at quasi-static and dynamic strain rates: Experimental and numerical study
Alper Tasdemirci et al.
THIN-WALLED STRUCTURES (2015)
Investigations Into the Influence of Weld Zone on Formability of Fiber Laser-Welded Advanced High Strength Steel
K. Bandyopadhyay et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2014)
A review on tailored blanks-Production, applications and evaluation
Marion Merklein et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2014)
Experimental study on crashworthiness of tailor-welded blank (TWB) thin-walled high-strength steel (HSS) tubular structures
Fengxiang Xu et al.
THIN-WALLED STRUCTURES (2014)
Numerical investigation of axial crushing behavior of a tailor welded tube
Hasan Gedikli
MATERIALS & DESIGN (2013)
Tensile and fatigue properties of fiber laser welded high strength low alloy and DP980 dual-phase steel joints
W. Xu et al.
MATERIALS & DESIGN (2013)
Crashworthiness investigation of conical and cylindrical end-capped tubes under quasi-static crash loading
Ali Ghamarian et al.
INTERNATIONAL JOURNAL OF CRASHWORTHINESS (2012)
Microstructure and fatigue performance of single and multiple linear fiber laser welded DP980 dual-phase steel
W. Xu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Optimization of laser welding of DP/TRIP steel sheets using statistical approach
U. Reisgen et al.
OPTICS AND LASER TECHNOLOGY (2012)
Energy-absorbing effectiveness factor
Norman Jones
INTERNATIONAL JOURNAL OF IMPACT ENGINEERING (2010)
Improvement in formability of tailor welded blanks by application of counter pressure in biaxial stretch forming
Sushanta Kumar Panda et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
A comparison study on the effectiveness of stepped binder and weld line clamping pins on formability improvement for tailor-welded blanks
W. Chen et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Influence of the weld conditions on the forming-limit strains of tailor-welded blanks
R. Ganesh Narayanan et al.
JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN (2008)
Impact modeling of the weld line of tailor-welded blank
Yuhang Shi et al.
MATERIALS & DESIGN (2008)
A comparative study of formability of diode laser welds in DP980 and HSLA steels
M. Xia et al.
JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY-TRANSACTIONS OF THE ASME (2007)
Experimental and numerical investigations into collapse behaviour of thin spherical shells under drop hammer impact
N. K. Gupta et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2007)
Effect of anisotropy on the deep-drawing of mild steel and dual-phase steel tailor-welded blanks
R. Padmanabhan et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)
Characterization of tensile properties of tailor welded IF steel sheets and their formability in stretch forming
Sushanta Kumar Panda et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)
An experimental and computational study of the crushing of metallic hemispherical shells between two rigid flat platens
P. K. Gupta et al.
JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN (2006)
Formability analysis of tailor-welded blanks of different thickness ratios
LC Chan et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2005)
Effect of laser welding parameters on the heat input and weld-bead profile
KY Benyounis et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2005)
Formability and weld zone analysis of tailor-welded blanks for various thickness ratios
LC Chan et al.
JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY-TRANSACTIONS OF THE ASME (2005)
Quasi-static and dynamic axial crushing of thin-walled circular stainless steel, mild steel and aluminium alloy tubes
SS Hsu et al.
INTERNATIONAL JOURNAL OF CRASHWORTHINESS (2004)
Crashworthiness assessment of front side members in an auto-body considering the fabrication histories
H Huh et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2003)
Formability enhancement for tailor-welded blanks using blank holding force control
SJ He et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2003)
The effect of the drawbead dimensions on the weld-line movements in the deep drawing of tailor-welded blanks
YM Heo et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)
Experimental and numerical studies of foam-filled sections
SP Santosa et al.
INTERNATIONAL JOURNAL OF IMPACT ENGINEERING (2000)
Tube hydroforming: current research, applications and need for training
M Ahmetoglu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2000)
A novel forming technology for tailor-welded blacks
B Kinsey et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2000)
Share Paper
