Related references
Note: Only part of the references are listed.Stress analysis of divertor plasma-facing component designs using tungsten particle-reinforced copper composite heat sink
Kuo Zhang et al.
FUSION ENGINEERING AND DESIGN (2020)
The design and optimisation of a monoblock divertor target for DEMO using thermal break interlayer
F. Domptail et al.
FUSION ENGINEERING AND DESIGN (2020)
Nuclear analyses for the design of the ITER-like plasma facing components vertical targets of the DEMO divertor
Simone Noce et al.
FUSION ENGINEERING AND DESIGN (2020)
Performance assessment of thick W/Cu graded interlayer for DEMO divertor target
M. Richou et al.
FUSION ENGINEERING AND DESIGN (2020)
Towards reliable design-by-analysis for divertor plasma facing components-Guidelines for inelastic assessment (part II: irradiated)
M. Fursdon et al.
FUSION ENGINEERING AND DESIGN (2020)
Ultrasonic test results before and after high heat flux testing on W-monoblock mock-ups of EU-DEMO vertical target
S. Roccella et al.
FUSION ENGINEERING AND DESIGN (2020)
Ultrasonic analysis of tungsten monoblock divertor mock-ups after high heat flux test
Giacomo Dose et al.
FUSION ENGINEERING AND DESIGN (2019)
High heat flux test results for a thermal break DEMO divertor target and subsequent design and manufacture development
Adomas Lukenskas et al.
FUSION ENGINEERING AND DESIGN (2019)
Progress in high heat flux testing of European DEMO divertor mock-ups
Henri Greuner et al.
FUSION ENGINEERING AND DESIGN (2019)
Manufacturing and testing of ITER-like divertor plasma facing mock-ups for DEMO
Eliseo Visca et al.
FUSION ENGINEERING AND DESIGN (2018)
The thermo-mechanical behaviour of W-Cu metal matrix composites for fusion heat sink applications: The influence of the Cu content
E. Tejado et al.
JOURNAL OF NUCLEAR MATERIALS (2018)
Evolution of mechanical performance with temperature of W/Cu and W/CuCrZr composites for fusion heat sink applications
E. Tejado et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Plasma exhaust and divertor studies in Japan and Europe broader approach, DEMO design activity
Nobuyuki Asakura et al.
FUSION ENGINEERING AND DESIGN (2018)
Structural impact of creep in tungsten monoblock divertor target at 20 MW/m2
Muyuan Li et al.
NUCLEAR MATERIALS AND ENERGY (2018)
The effects of heat treatment at temperatures of 1100 °C to 1300 °C on the tensile properties of high-strength drawn tungsten fibres
A. v. Mueller et al.
NUCLEAR MATERIALS AND ENERGY (2018)
European divertor target concepts for DEMO: Design rationales and high heat flux performance
J. H. You et al.
NUCLEAR MATERIALS AND ENERGY (2018)
Fracture mechanical analysis of a tungsten monoblock-type plasma-facing component without macroscopic interlayer for high-heat-flux divertor target
Muyuan Li et al.
FUSION ENGINEERING AND DESIGN (2017)
Progress in the initial design activities for the European DEMO divertor: Subproject Cassette
J. H. You et al.
FUSION ENGINEERING AND DESIGN (2017)
Design options to mitigate deep cracking of tungsten armor
Muyuan Li et al.
FUSION ENGINEERING AND DESIGN (2017)
ITER-like divertor target for DEMO: Design study and fabrication test
F. Crescenzi et al.
FUSION ENGINEERING AND DESIGN (2017)
Sweeping heat flux loads on divertor targets: Thermal benefits and structural impacts
Muyuan Li et al.
FUSION ENGINEERING AND DESIGN (2016)
Structural impact of armor monoblock dimensions on the failure behavior of ITER-type divertor target components: Size matters
Muyuan Li et al.
FUSION ENGINEERING AND DESIGN (2016)
Limitations of transient power loads on DEMO and analysis of mitigation techniques
F. Maviglia et al.
FUSION ENGINEERING AND DESIGN (2016)
Overview of the design approach and prioritization of R&D activities towards an EU DEMO
G. Federici et al.
FUSION ENGINEERING AND DESIGN (2016)
European DEMO divertor target: Operational requirements and material-design interface
J. H. You et al.
NUCLEAR MATERIALS AND ENERGY (2016)
Low cycle fatigue behavior of ITER-like divertor target under DEMO-relevant operation conditions
Muyuan Li et al.
FUSION ENGINEERING AND DESIGN (2015)
European roadmap to the realization of fusion energy: Mission for solution on heat-exhaust systems
M. Turnyanskiy et al.
FUSION ENGINEERING AND DESIGN (2015)
Interpretation of the deep cracking phenomenon of tungsten monoblock targets observed in high-heat-flux fatigue tests at 20 MW/m2
Muyuan Li et al.
FUSION ENGINEERING AND DESIGN (2015)
A review on two previous divertor target concepts for DEMO: mutual impact between structural design requirements and materials performance
Jeong-Ha You
NUCLEAR FUSION (2015)
Qualification and post-mortem characterization of tungsten mock-ups exposed to cyclic high heat flux loading
G. Pintsuk et al.
FUSION ENGINEERING AND DESIGN (2013)
Thermal and mechanical properties of infiltrated W/CuCrZr composite materials for functionally graded heat sink application
J. -H. You et al.
JOURNAL OF NUCLEAR MATERIALS (2013)
ITER plasma-facing components
Mario Merola et al.
FUSION ENGINEERING AND DESIGN (2010)
High heat flux facility GLADIS: Operational characteristics and results of W7-X pre-series target tests
H. Greuner et al.
JOURNAL OF NUCLEAR MATERIALS (2007)
Overall mechanical properties of fiber-reinforced metal matrix composites for fusion applications
JH You et al.
JOURNAL OF NUCLEAR MATERIALS (2002)
Analysis of singular interface stresses in dissimilar material joints for plasma facing components
JH You et al.
JOURNAL OF NUCLEAR MATERIALS (2001)
Share Paper
