Related references
Note: Only part of the references are listed.A numerical study on the effect of cavitation erosion in a diesel injector
Marco Cristofaro et al.
APPLIED MATHEMATICAL MODELLING (2020)
Real-fluid injection modeling and LES simulation of the ECN Spray A injector using a fully compressible two-phase flow approach
Songzhi Yang et al.
INTERNATIONAL JOURNAL OF MULTIPHASE FLOW (2020)
Vapor-liquid equilibrium calculations at specified composition, density and temperature with the perturbed chain statistical associating fluid theory (PC-SAFT) equation of state
Alvaro Vidal et al.
FLUID PHASE EQUILIBRIA (2020)
Influence of Diesel Fuel Viscosity on Cavitating Throttle Flow Simulations under Erosive Operation Conditions
Marco Cristofaro et al.
ACS OMEGA (2020)
An experimental study of a very high-pressure diesel injector (up to 5000 bar) by means of optical diagnostics
W. Vera-Tudela et al.
FUEL (2020)
General method for prediction of thermal conductivity for well-characterized hydrocarbon mixtures and fuels up to extreme conditions using entropy scaling
Houman B. Rokni et al.
FUEL (2019)
Numerical and experimental investigation of shedding mechanisms from leading-edge cavitation
Mohammad Hossein Arabnejad et al.
INTERNATIONAL JOURNAL OF MULTIPHASE FLOW (2019)
Effect of Composition, Temperature, and Pressure on the Viscosities and Densities of Three Diesel Fuels
Aaron J. Rowane et al.
JOURNAL OF CHEMICAL AND ENGINEERING DATA (2019)
Purely predictive method for density, compressibility, and expansivity for hydrocarbon mixtures and diesel and jet fuels up to high temperatures and pressures
Houman B. Rokni et al.
FUEL (2019)
A comparative study between numerical methods in simulation of cavitating bubbles
Ebrahim Ghahramani et al.
INTERNATIONAL JOURNAL OF MULTIPHASE FLOW (2019)
Experimental investigation of the effects of diesel fuel properties on combustion and emissions on a multi-cylinder heavy-duty diesel engine
Haifeng Liu et al.
ENERGY CONVERSION AND MANAGEMENT (2018)
Simulations on the cavitating flow and corresponding risk of erosion in diesel injector nozzles with double array holes
Liang Zhang et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2018)
The influence of eccentric needle movement on internal flow and injection characteristics of a multi-hole diesel nozzle
Chuqiao Wang et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2018)
High-speed visualization of vortical cavitation using synchrotron radiation
Ioannis K. Karathanassis et al.
JOURNAL OF FLUID MECHANICS (2018)
Turbulence and Cavitation Suppression by Quaternary Ammonium Salt Additives
Homa Naseri et al.
SCIENTIFIC REPORTS (2018)
Illustrating the effect of viscoelastic additives on cavitation and turbulence with X-ray imaging
I. K. Karathanassis et al.
SCIENTIFIC REPORTS (2018)
Large-Eddy Simulation of turbulent, cavitating fuel flow inside a 9-hole Diesel injector including needle movement
Felix Oerley et al.
INTERNATIONAL JOURNAL OF ENGINE RESEARCH (2017)
Performance of turbulence and cavitation models in prediction of incipient and developed cavitation
Phoevos Koukouvinis et al.
INTERNATIONAL JOURNAL OF ENGINE RESEARCH (2017)
Thermal Conductivity of Real Substances from Excess Entropy Scaling Using PCP-SAFT
Madlen Hopp et al.
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2017)
Numerical simulation of compressible cavitating two-phase flows with a pressure-based solver
Marco Cristofaro et al.
28TH CONFERENCE ON LIQUID ATOMIZATION AND SPRAY SYSTEMS, ILASS-EUROPE 2017 (2017)
Diesel Surrogate Fuels for Engine Testing and Chemical-Kinetic Modeling: Compositions and Properties
Charles J. Mueller et al.
ENERGY & FUELS (2016)
Large Eddy Simulation of Diesel injector including cavitation effects and correlation to erosion damage
Phoevos Koukouvinis et al.
FUEL (2016)
Boundary condition and fuel composition effects on injection processes of high-pressure sprays at the microscopic level
J. Manin et al.
INTERNATIONAL JOURNAL OF MULTIPHASE FLOW (2016)
PVT modeling of reservoir fluids using PC-SAFT EoS and Soave-BWR EoS
Wei Yan et al.
FLUID PHASE EQUILIBRIA (2015)
Group Contribution Method for Viscosities Based on Entropy Scaling Using the Perturbed-Chain Polar Statistical Associating Fluid Theory
Oliver Loetgering-Lin et al.
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2015)
Transient heating effects in high pressure Diesel injector nozzles
George Strotos et al.
INTERNATIONAL JOURNAL OF HEAT AND FLUID FLOW (2015)
On the formation of string cavitation inside fuel injectors
B. A. Reid et al.
EXPERIMENTS IN FLUIDS (2014)
Instantaneous and ensemble average cavitation structures in Diesel micro-channel flow orifices
Nicholas Mitroglou et al.
FUEL (2014)
Friction-induced heating in nozzle hole micro-channels under extreme fuel pressurisation
Andreas Theodorakakos et al.
FUEL (2014)
Comparison of Mixture and Multifluid Models for In-Nozzle Cavitation Prediction
Michele Battistoni et al.
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME (2014)
Phase behavior of reservoir fluids: Comparisons of PC-SAFT and cubic EOS simulations
Sukit Leekumjorn et al.
FLUID PHASE EQUILIBRIA (2013)
Volume-translated cubic EoS and PC-SAFT density models and a free volume-based viscosity model for hydrocarbons at extreme temperature and pressure conditions
Ward A. Burgess et al.
FLUID PHASE EQUILIBRIA (2013)
Evaluation of the PC-SAFT, SAFT and CPA equations of state in predicting derivative properties of selected non-polar and hydrogen-bonding compounds
A. J. de Villiers et al.
FLUID PHASE EQUILIBRIA (2013)
Mapping of cavitating flow regimes in injectors for medium-/heavy-duty diesel engines
Nicholas Mitroglou et al.
INTERNATIONAL JOURNAL OF ENGINE RESEARCH (2013)
Modeling thermodynamic properties of natural gas mixtures using perturbed-chain statistical associating fluid theory
Mahmood Farzaneh Gord et al.
RUSSIAN JOURNAL OF APPLIED CHEMISTRY (2013)
Mass loss simulation in cavitation erosion: Fatigue criterion approach
Regiane Fortes Patella et al.
WEAR (2013)
Combination of Visualization Techniques for the Analysis of Evaporating Diesel Sprays
R. Payri et al.
ENERGY & FUELS (2012)
A discrete multicomponent fuel evaporation model with liquid turbulence effects
O. Samimi Abianeh et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2012)
High-pressure vaporization modeling of multi-component petroleum-biofuel mixtures under engine conditions
Lei Zhang et al.
COMBUSTION AND FLAME (2011)
Numerical investigation of the evaporation of two-component droplets
George Strotos et al.
FUEL (2011)
The potential of Large Eddy Simulation (LES) code for the modeling of flow in diesel injectors
R. Payri et al.
MATHEMATICAL AND COMPUTER MODELLING (2010)
An investigation of string cavitation in a true-scale fuel injector flow geometry at high pressure
B. A. Reid et al.
PHYSICS OF FLUIDS (2010)
Effect of Bioethanol-Biodiesel Blending Ratio on Fuel Spray Behavior and Atomization Characteristics
Su Han Park et al.
ENERGY & FUELS (2009)
Mixing Stability and Spray Behavior Characteristics of Diesel-Ethanol-Methyl Ester Blended Fuels in a Common-Rail Diesel Injection System
Su Han Park et al.
ENERGY & FUELS (2009)
Characterization of string cavitation in large-scale Diesel nozzles with tapered holes
M. Gavaises et al.
PHYSICS OF FLUIDS (2009)
Experimental comparison of soot formation in turbulent flames of Diesel and surrogate Diesel fuels
R. Lemaire et al.
PROCEEDINGS OF THE COMBUSTION INSTITUTE (2009)
Diesel nozzle geometry influence on spray liquid-phase fuel penetration in evaporative conditions
R. Payri et al.
FUEL (2008)
Flow in valve covered orifice nozzles with cylindrical and tapered holes and link to cavitation erosion and engine exhaust emissions
M. Gavaises
INTERNATIONAL JOURNAL OF ENGINE RESEARCH (2008)
Modelling of cavitation in diesel injector nozzles
E. Giannadakis et al.
JOURNAL OF FLUID MECHANICS (2008)
Modelling phase transition in metastable liquids: application to cavitating and flashing flows
Richard Saurel et al.
JOURNAL OF FLUID MECHANICS (2008)
Multidimentional simulation of cavitating flows in diesel injectors by a homogeneous mixture modeling approach
Chawki Habchi et al.
ATOMIZATION AND SPRAYS (2008)
Effects of cavitation in a nozzle on liquid jet atomization
Akira Sou et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2007)
The role of additives for diesel and diesel blended (Ethanol or biodiesel) fuels: A review
Nubia M. Ribeiro et al.
ENERGY & FUELS (2007)
Soot in diesel fuel jets: effects of ambient temperature, ambient density, and injection pressure
LM Pickett et al.
COMBUSTION AND FLAME (2004)
A study of the relation between nozzle geometry, internal flow and sprays characteristics in diesel fuel injection systems
R Payri et al.
KSME INTERNATIONAL JOURNAL (2004)
Numerical simulation of two-phase flow in injection nozzles: Interaction of cavitation and external jet formation
MX Yuan et al.
JOURNAL OF FLUIDS ENGINEERING-TRANSACTIONS OF THE ASME (2003)
Mathematical basis and validation of the full cavitation model
AK Singhal et al.
JOURNAL OF FLUIDS ENGINEERING-TRANSACTIONS OF THE ASME (2002)
High Reynolds number, unsteady, multiphase CFD modeling of cavitating flows
JW Lindau et al.
JOURNAL OF FLUIDS ENGINEERING-TRANSACTIONS OF THE ASME (2002)
Perturbed-chain SAFT: An equation of state based on a perturbation theory for chain molecules
J Gross et al.
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2001)