Related references
Note: Only part of the references are listed.Contribution of intragranular misorientations to the cold rolling textures of ferritic stainless steels
A. Despres et al.
ACTA MATERIALIA (2020)
A detailed study of texture changes during alpha-beta processing of a zirconium alloy
Christopher S. Daniel et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2019)
Reverse Transformation Behavior of Ti-6Al-4V After Deformation in the Two-Phase Region
Baoqi Guo et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2018)
Opposing and Driving Forces Associated with the Dynamic Transformation of Ti-6Al-4V
Baoqi Guo et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2018)
Effect of the presence of macrozones on short crack propagation in forged two-phase titanium alloys
K. Zhang et al.
INTERNATIONAL JOURNAL OF FATIGUE (2017)
On recrystallization of the α and β phases in titanium alloys
Shanoob Balachandran et al.
ACTA MATERIALIA (2017)
Microstructure and texture evolution during thermomechanical processing of beta-quenched Zr
D. G. Leo Prakash et al.
ACTA MATERIALIA (2015)
⟨a⟩ Prismatic, ⟨a⟩ basal, and ⟨c plus a⟩ slip strengths of commercially pure Zr by micro-cantilever tests
Jicheng Gong et al.
ACTA MATERIALIA (2015)
Grain Breakup During Elevated Temperature Deformation of an HCP Metal
Peter D. Honniball et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2015)
Characterization and influence of deformation microstructure heterogeneity on recrystallization
A. Godfrey et al.
36TH RISO INTERNATIONAL SYMPOSIUM ON MATERIALS SCIENCE (2015)
Variant selection of grain boundary α by special prior β grain boundaries in titanium alloys
R. Shi et al.
ACTA MATERIALIA (2014)
Crystallographic texture and microstructure evolution during hot compression of Ti-6Al-4V-0.1B alloy in the (α plus β)-regime
Shibayan Roy et al.
PHILOSOPHICAL MAGAZINE (2014)
DREAM. 3D: A Digital Representation Environment for the Analysis of Microstructure in 3D
Michael A. Groeber et al.
INTEGRATING MATERIALS AND MANUFACTURING INNOVATION (2014)
Role of mechanical activation in the dynamic transformation of austenite
John J. Jonas et al.
ACTA MATERIALIA (2013)
Variant selection during α precipitation in Ti-6Al-4V under the influence of local stress - A simulation study
R. Shi et al.
ACTA MATERIALIA (2013)
The effect of β phase on microstructure and texture evolution during thermomechanical processing of α plus β Ti alloy
D. G. Leo Prakash et al.
ACTA MATERIALIA (2013)
Study of microstructure, texture and mechanical properties of Zr-2.5Nb alloy pressure tubes fabricated with different processing routes
N. Saibaba et al.
JOURNAL OF NUCLEAR MATERIALS (2013)
Deformation of high β-phase fraction Zr-Nb alloys at room temperature
S. Cai et al.
ACTA MATERIALIA (2012)
The influence of rolling temperature on texture evolution and variant selection during α → β → α phase transformation in Ti-6Al-4V
G. C. Obasi et al.
ACTA MATERIALIA (2012)
The role of microtexture on the faceted fracture morphology in Ti-6Al-4V subjected to high-cycle fatigue
Ioannis Bantounas et al.
ACTA MATERIALIA (2010)
Texture inheritance and variant selection through an hcp-bcc-hcp phase transformation
M. R. Daymond et al.
ACTA MATERIALIA (2010)
Deformation twinning in Ti-6Al-4V during low strain rate deformation to moderate strains at room temperature
D. G. Leo Prakash et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
Evolution of interphase and intergranular stresses in Zr-2.5Nb during room temperature deformation
S. Cai et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)
Modeling of texture evolution during hot forging of alpha/beta titanium alloys
M. G. Glavicic et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2008)
Accuracy of orientation distribution function determination based on EBSD data-A case study of a recrystallized low alloyed Zr sheet
N. Bozzolo et al.
JOURNAL OF MICROSCOPY (2007)
Development of local microstructure and crystallographic texture in extruded Zr-2.5Nb tubes
Y. Li et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)
Study of the variant selection in sharp textured regions of bimodal IMI 834 billet
M. Humbert et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)
Analysis of sharp microtexture heterogeneities in a bimodal IMI 834 billet
L Germain et al.
ACTA MATERIALIA (2005)
Texture development in the cold rolling of IF steel
PS Bate et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2004)
Micro-texture of extruded Zr-2.5Nb tubes
RA Holt et al.
JOURNAL OF NUCLEAR MATERIALS (2004)
Elasticity-based model of the variant selection observed in the β to α phase transformation of a Zircalloy-4 sample
M Humbert et al.
ACTA MATERIALIA (2003)
The role of crystallographic and geometrical relationships between α and β phases in an α/β titanium alloy
D Bhattacharyya et al.
ACTA MATERIALIA (2003)
Explaining absence of texture development in cold rolled two-phase Zr-2.5 wt% Nb alloy
MK Kumar et al.
ACTA MATERIALIA (2003)
Microstructural evolution of a Ti-6Al-4V alloy during thermomechanical processing
R Ding et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2002)
Evolution of recrystallisation texture and microstructure in low alloyed titanium sheets
F Wagner et al.
ACTA MATERIALIA (2002)
The origins of heterogeneous deformation during primary hot working of Ti-6Al-4V
TR Bieler et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2002)
The effect of alpha platelet thickness on plastic flow during hot working of Ti-6Al-4V with a transformed microstructure
SL Semiatin et al.
ACTA MATERIALIA (2001)
Sensitivity of α-Zy4 high-temperature deformation textures to the β-quenched precipitate structure and to recrystallization:: Application to hot extrusion
RE Logé et al.
ACTA MATERIALIA (2000)