Related references
Note: Only part of the references are listed.Constructal Design for the ultimate buckling stress improvement of stiffened plates submitted to uniaxial compressive load
Joao Paulo Silva Lima et al.
ENGINEERING STRUCTURES (2020)
Small scale experimental validation of a numerical model of the HarshLab2.0 floating platform coupled with a non-linear lumped mass catenary mooring system
Imanol Touzon et al.
OCEAN ENGINEERING (2020)
Computational Modeling and Constructal Design Theory Applied to the Geometric Optimization of Thin Steel Plates with Stiffeners Subjected to Uniform Transverse Load
Gregori Troina et al.
METALS (2020)
Multi-floater-mooring coupled time-domain hydro-elastic analysis in regular and irregular waves
Chungkuk Jin et al.
APPLIED OCEAN RESEARCH (2020)
Numerical Analysis of the Influence of Empty Channels Design on Performance of Resin Flow in a Porous Plate
Glaucileia M. C. Magalhaes et al.
APPLIED SCIENCES-BASEL (2020)
Geometric optimization of a lid-driven cavity with two rectangular intrusions under mixed convection heat transfer: A numerical investigation motivated by constructal design
P. M. Rodrigues et al.
INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER (2020)
A survey on modeling and control of thruster-assisted position mooring systems
Roger Skjetne et al.
MARINE STRUCTURES (2020)
Prediction of the whole mooring chain reaction to cyclic motion of a fairlead
Kanmin Shen et al.
BULLETIN OF ENGINEERING GEOLOGY AND THE ENVIRONMENT (2019)
Constructal Design of Aircraft: Flow of Stresses and Aeroelastic Stability
Pezhman Mardanpour et al.
AIAA JOURNAL (2019)
Numerical buckling analysis of thin steel plates with centered hexagonal perforation through constructal design method
Caio Cesar Cardoso da Silva et al.
JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2019)
Efficient discrete element simulation of managed ice actions on moored floating platforms
Mochamad Raditya Pradana et al.
OCEAN ENGINEERING (2019)
Geometric Evaluation of Stiffened Steel Plates Subjected to Transverse Loading for Naval and Offshore Applications
Joao Pedro T. P. de Queiroz et al.
JOURNAL OF MARINE SCIENCE AND ENGINEERING (2019)
ABAQUS IMPLEMENTATION OF A COROTATIONAL PIEZOELECTRIC 3-NODE SHELL ELEMENT WITH DRILLING DEGREE OF FREEDOM
Dragan Marinkovic et al.
FACTA UNIVERSITATIS-SERIES MECHANICAL ENGINEERING (2019)
Study on green water prediction for FPSOs by a practical numerical approach
Shuo Wang et al.
OCEAN ENGINEERING (2017)
Experimental investigations into the current-induced motion of a lifeboat at a single point mooring
Catherine J. Hollyhead et al.
OCEAN ENGINEERING (2017)
Experimental validation of a dynamic mooring lines code with tension and motion measurements of a submerged chain
Jose Azcona et al.
OCEAN ENGINEERING (2017)
Numerical evaluation of a solar chimney geometry for different ground temperatures by means of constructal design
R. S. Vieira et al.
RENEWABLE ENERGY (2017)
Computational Modeling and Constructal Design Method Applied to the Mechanical Behavior Improvement of Thin Perforated Steel Plates Subject to Buckling
G. Lorenzini et al.
JOURNAL OF ENGINEERING THERMOPHYSICS (2016)
A comparison of simulated annealing schedules for constructal design of complex cavities intruded into conductive walls with internal heat generation
G. V. Gonzales et al.
ENERGY (2015)
Fatigue analysis of deepwater hybrid mooring line under corrosion effect
Dongsheng Qiao et al.
POLISH MARITIME RESEARCH (2014)
Comparison and Sensitivity Investigations of a CALM and SALM Type Mooring System for Wave Energy Converters
Arthur Pecher et al.
JOURNAL OF MARINE SCIENCE AND ENGINEERING (2014)
GEOMETRIC OPTIMIZATION BASED ON THE CONSTRUCTAL DESIGN OF PERFORATED THIN PLATES SUBJECT TO BUCKLING
L. A. O. Rocha et al.
COMPUTATIONAL THERMAL SCIENCES (2012)
Vessel/mooring/riser coupled dynamic analysis of a turret-moored FPSO compared with OTRC experiment
MH Kim et al.
OCEAN ENGINEERING (2005)
Share Paper
