Related references
Note: Only part of the references are listed.Wear behaviour of whisker-reinforced ceramic tools in the turning of Inconel 718 assisted by an atomized spray of solid lubricants
Vinothkumar Sivalingam et al.
TRIBOLOGY INTERNATIONAL (2020)
Influence of CO2-snow and subzero MQL on thermal aspects in the machining of Ti-6Al-4V
Muhammad Jamil et al.
APPLIED THERMAL ENGINEERING (2020)
Machining characteristics based life cycle assessment in eco-benign turning of pure titanium alloy
Munish Kumar Gupta et al.
JOURNAL OF CLEANER PRODUCTION (2020)
Evaluation of tool wear, surface roughness/topography and chip morphology when machining of Ni-based alloy 625 under MQL, cryogenic cooling and CryoMQL
Cagri Vakkas Yildirim et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)
Exploration of graphene assisted vegetables oil based minimum quantity lubrication for surface grinding of TI-6AL-4V-ELI
Harpinder Singh et al.
TRIBOLOGY INTERNATIONAL (2020)
Sustainability-based performance evaluation of hybrid nanofluid assisted machining
Aqib Mashood Khan et al.
JOURNAL OF CLEANER PRODUCTION (2020)
Sustainability and machinability improvement of Nimonic-90 using indigenously developed green hybrid machining technology
Navneet Khanna et al.
JOURNAL OF CLEANER PRODUCTION (2020)
Energy-based cost integrated modelling and sustainability assessment of Al-GnP hybrid nanofluid assisted turning of AISI52100 steel
Aqib Mashood Khan et al.
JOURNAL OF CLEANER PRODUCTION (2020)
Low carbon roadmap of residential building sector in China: Historical mitigation and prospective peak
Minda Ma et al.
APPLIED ENERGY (2020)
Machining performance of vegetable oil with phosphonium- and ammonium-based ionic liquids via MQL technique
Amiril Sahab Abdul Sani et al.
JOURNAL OF CLEANER PRODUCTION (2019)
Nanofluids assisted environmental friendly lubricating strategies for the surface grinding of titanium alloy: Ti6Al4V-ELI
Harpinder Singh et al.
JOURNAL OF MANUFACTURING PROCESSES (2019)
Ecological trends in machining as a key factor in sustainable production - A review
G. M. Krolczyk et al.
JOURNAL OF CLEANER PRODUCTION (2019)
Performance evaluation of vegetable-based cutting fluids in turning of AISI 1050 steel
Deborah Oliveira Almeida Carvalho et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Machining and environmental effects of electrostatic atomization lubrication in milling operation
Yu Su et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
The effect of addition of hBN nanoparticles to nanofluid-MQL on tool wear patterns, tool life, roughness and temperature in turning of Ni-based Inconel 625
Cagri Vakkas Yildirim et al.
TRIBOLOGY INTERNATIONAL (2019)
Influence of graphene-enriched nanofluids and textured tool on machining behavior of Ti-6Al-4V alloy
Rupinder Singh et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Performance Evaluation of Vegetable Oil-Based Nano-Cutting Fluids in Environmentally Friendly Machining of Inconel-800 Alloy
Munish Kumar Gupta et al.
MATERIALS (2019)
Developing low carbon economies: An aggregated composite index based on carbon emissions
Muhammad Mohsin et al.
SUSTAINABLE ENERGY TECHNOLOGIES AND ASSESSMENTS (2019)
Hybrid cooling-lubrication strategies to improve surface topography and tool wear in sustainable turning of Al 7075-T6 alloy
Munish Kumar Gupta et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Experimental study of vortex tube energy separation under different tube design
Mohammad O. Hamdan et al.
EXPERIMENTAL THERMAL AND FLUID SCIENCE (2018)
An approach to cleaner production for machining hardened steel using different cooling-lubrication conditions
Mozammel Mia et al.
JOURNAL OF CLEANER PRODUCTION (2018)
Influence of Ranque-Hilsch vortex tube and nitrogen gas assisted MQL in precision turning of Al 6061-T6
Mozammel Mia et al.
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2018)
An alternative to carbon taxes to finance renewable energy systems and offset hydrocarbon based greenhouse gas emissions
David D. J. Taylor et al.
SUSTAINABLE ENERGY TECHNOLOGIES AND ASSESSMENTS (2017)
Analysis of cutting parameters and cooling/lubrication methods for sustainable machining in turning of Haynes 25 superalloy
Murat Sarikaya et al.
JOURNAL OF CLEANER PRODUCTION (2016)
Tool wear in Ti-6Al-4V alloy turning under oils on water cooling comparing with cryogenic air mixed with minimal quantity lubrication
Haisheng Lin et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Application of sustainable techniques in metal cutting for enhanced machinability: a review
Chetan et al.
JOURNAL OF CLEANER PRODUCTION (2015)
Multi-response optimization of minimum quantity lubrication parameters using Taguchi-based grey relational analysis in turning of difficult-to-cut alloy Haynes 25
Murat Sarikaya et al.
JOURNAL OF CLEANER PRODUCTION (2015)
Performance Evaluation of Coated Carbide Tool in Machining of Stainless Steel (AISI 202) under Minimum Quantity Lubrication (MQL)
J. S. Dureja et al.
INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING-GREEN TECHNOLOGY (2015)
Environmental friendly cutting fluids and cooling techniques in machining: a review
Sujan Debnath et al.
JOURNAL OF CLEANER PRODUCTION (2014)
VORTEX TUBE AIR COOLING: THE EFFECT ON SURFACE ROUGHNESS AND POWER CONSUMPTION IN DRY TURNING
Zahari Taha et al.
INTERNATIONAL JOURNAL OF AUTOMOTIVE AND MECHANICAL ENGINEERING (2013)
Machining of β-titanium-alloy Ti-10V-2Fe-3Al under cryogenic conditions: Cooling with carbon dioxide snow
Christian Machai et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2011)
Investigation of tool wear and surface integrity on MQL machining of Ti-6AL-4V using biodegradable oil
E. A. Rahim et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2011)
Cooling techniques for improved productivity in turning
Vishal S. Sharma et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2009)
Improving tool life using cryogenic cooling
Ahsan Ali Khan et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Particle size distributions of oil mists in workplace atmospheres and their exposure concentrations to workers in a fastener manufacturing industry
Mei-Ru Chen et al.
JOURNAL OF HAZARDOUS MATERIALS (2007)