Related references
Note: Only part of the references are listed.Effect of welding parameters on microstructure and mechanical properties of AA7075/AA5182 alloys joined by TIG and MIG welding methods
Edip Cetkin et al.
JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2020)
Experimental investigation on novel drilling strategy of CFRP laminates using variable feed rate
Nafiz Yasar et al.
JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2019)
Microstructure and mechanical properties of AA7075/AA5182 jointed by FSW
Edip Cetkin et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)
Optimisation of process parameters for the orbital and conventional drilling of uni-directional carbon fibre-reinforced polymers (UD-CFRP)
Norbert Geier et al.
MEASUREMENT (2017)
Low-frequency modulation-assisted drilling of carbon-epoxy composite laminates
Kishore Debnath et al.
JOURNAL OF MANUFACTURING PROCESSES (2017)
Experimental investigation of clamping systems and the resulting change of cutting conditions while drilling carbon fiber reinforced plastics
Stefan Klotz et al.
10TH CIRP CONFERENCE ON INTELLIGENT COMPUTATION IN MANUFACTURING ENGINEERING - CIRP ICME '16 (2017)
Comparative assessment of support plates' influences on delamination damage in micro-drilling of CFRP laminates
A. Dogrusadik et al.
COMPOSITE STRUCTURES (2017)
Influence of drilling and abrasive water jet induced damage on the performance of carbon fabric/epoxy plates with holes
John Montesano et al.
COMPOSITE STRUCTURES (2017)
Soft computing techniques during drilling of bi-directional carbon fiber reinforced composite
Nagaraja Shetty et al.
APPLIED SOFT COMPUTING (2016)
Numerical analysis of the influence of tool wear and special cutting geometry when drilling woven CFRPs
N. Feito et al.
COMPOSITE STRUCTURES (2016)
The effect of drilling-induced delamination on tensile strength and prediction of residual strength of carbon fiber-reinforced polymer laminate
Chongcong Tao et al.
JOURNAL OF COMPOSITE MATERIALS (2016)
CFRP drilling: Fundamental study of local feed force and consequences on hole exit damage.
Cedric Bonnet et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2015)
Progressive Failure Analysis of Laminated Composite Plates With Two Serial Pinned Joints
Kadir Turan et al.
MECHANICS OF ADVANCED MATERIALS AND STRUCTURES (2015)
A comparative evaluation of polycrystalline diamond drills in drilling high-strength T800S/250F CFRP
Jinyang Xu et al.
COMPOSITE STRUCTURES (2014)
Experimental Analysis of the Influence of Drill Point Angle and Wear on the Drilling of Woven CFRPs
Norberto Feito et al.
MATERIALS (2014)
Experimental study of surface quality and damage when drilling unidirectional CFRP composites
Eshetu D. Eneyew et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2014)
A review of modeling and control during drilling of fiber reinforced plastic composites
Amrinder Pal Singh et al.
COMPOSITES PART B-ENGINEERING (2013)
A review of mechanical drilling for composite laminates
DeFu Liu et al.
COMPOSITE STRUCTURES (2012)
Influence of Point Angle on Drill Hole Quality and Machining Forces when Drilling CFRP
Uwe Heisel et al.
FIFTH CIRP CONFERENCE ON HIGH PERFORMANCE CUTTING 2012 (2012)
Investigation into the effect of drilling parameters on delamination in drilling GFRP
Erol Kilickap
JOURNAL OF REINFORCED PLASTICS AND COMPOSITES (2010)
Characterization of the dry high speed drilling process of woven composites using Machinability Maps approach
Sanjay Rawat et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2009)
Analysis of parametric influence on delamination in high-speed drilling of carbon fiber reinforced plastic composites
V. N. Gaitonde et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Delamination analysis in high speed drilling of carbon fiber reinforced plastics (CFRP) using artificial neural network model
S. R. Karnik et al.
MATERIALS & DESIGN (2008)
The effect of cutting tool geometry on thrust force and delamination when drilling glass fibre reinforced plastic composite
A. M. Abrao et al.
MATERIALS & DESIGN (2008)
Drilling of uni-directional glass fiber reinforced plastics: Experimental and finite element study
I. Singh et al.
MATERIALS & DESIGN (2008)
Multi-objective optimization of cutting parameters for drilling laminate composite materials by using genetic algorithms
Ramon Quiza Sardinas et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2006)
Influence of tool material on dynamics of drilling of GFRP composites
S. Arul et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2006)
Numerical simulation of the drilling process on carbon/epoxy composite laminates
L. M. P. Durao et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2006)
The path towards delamination-free drilling of composite materials
H Hocheng et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2005)
Delamination in drilling GFR-thermoset composites
UA Khashaba
COMPOSITE STRUCTURES (2004)
Experimental study of drilling glass fiber reinforced plastics (GFRP) manufactured by hand lay-up
JP Davim et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2004)
Drilling carbon fiber reinforced plastics manufactured by autoclave - experimental and statistical study
JP Davim et al.
MATERIALS & DESIGN (2003)
Study of delamination in drilling carbon fiber reinforced plastics (CFRP) using design experiments
JP Davim et al.
COMPOSITE STRUCTURES (2003)
Share Paper
