Related references
Note: Only part of the references are listed.Microstructure, texture and hardness of a metastable β-titanium alloy after bar-rolling and annealing
B. Gu et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2020)
Effects of laser shock peening on microstructures and properties of 2195 Al-Li alloy
Yang Yang et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2019)
Gradient plastic strain accommodation and nanotwinning in multi-pass laser shock peened 321 steel
D. Karthik et al.
APPLIED SURFACE SCIENCE (2019)
Microstructure evolution and mechanical properties of aging 6061 Al alloy via laser shock processing
C. Y. Cui et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2019)
Effects of service temperature on tensile properties and microstructural evolution of CP titanium subjected to laser shock peening
H. F. Lu et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2019)
Surface gradient microstructural characteristics and evolution mechanism of 2195 aluminum lithium alloy induced by laser shock peening
Yang Yang et al.
OPTICS AND LASER TECHNOLOGY (2019)
Individual effect of recrystallisation nucleation sites on texture weakening in a magnesium alloy: Part 2-shear bands
Dikai Guan et al.
ACTA MATERIALIA (2018)
Dynamic recrystallization of titanium: Effect of pre-activated twinning at cryogenic temperature
C. K. Yan et al.
ACTA MATERIALIA (2018)
Gradient twinning microstructure generated by laser shock peening in an AZ31B magnesium alloy
Bo Mao et al.
APPLIED SURFACE SCIENCE (2018)
Thermal stability of microstructures induced by laser shock peening in TC17 titanium alloy
Yang Yang et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2018)
Evolution of microstructure and grain refinement mechanism of pure nickel induced by laser shock peening
Lan Chen et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Tensile properties and surface nanocrystallization analyses of H62 brass subjected to room-temperature and warm laser shock peening
J. Z. Lu et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2017)
Microstructure characteristics and formation mechanism of TC17 titanium alloy induced by laser shock processing
Yang Yang et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2017)
Adiabatic shear behaviors in rolled and annealed pure titanium subjected to dynamic impact loading
Lianjun Kuang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Microstructures and mechanical properties of β forging Ti17 alloy under combined laser shock processing and shot peening
Junfeng Wu et al.
SURFACE & COATINGS TECHNOLOGY (2017)
Microstructural response and grain refinement mechanism of commercially pure titanium subjected to multiple laser shock peening impacts
J. Z. Lu et al.
ACTA MATERIALIA (2017)
Microstructural characterisation of metallic shot peened and laser shock peened Ti-6Al-4V
Steven J. Laine et al.
ACTA MATERIALIA (2017)
Twinning effects on the hot deformation behavior of AZ31 Mg alloy
Yuanli Chen et al.
MATERIALS CHARACTERIZATION (2016)
Dynamic softening mechanism in Ti-13V-11Cr-3Al beta Ti alloy during hot compressive deformation
S. M. Abbasi et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
A review of dynamic recrystallization phenomena in metallic materials
K. Huang et al.
MATERIALS & DESIGN (2016)
Microstructural characteristics of adiabatic shear localization in a metastable beta titanium alloy deformed at high strain rate and elevated temperatures
Hongyi Zhan et al.
MATERIALS CHARACTERIZATION (2015)
Triggering rare earth texture modification in magnesium alloys by addition of zinc and zirconium
I. Basu et al.
ACTA MATERIALIA (2014)
Effect of laser shock peening on the mechanical properties of a near-α titanium alloy
Weiju Jia et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Experiment investigation of laser shock peening on TC6 titanium alloy to improve high cycle fatigue performance
Xiangfan Nie et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Shear band-related recrystallization and grain growth in two rolled magnesium-rare earth alloys
I. Basu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
Improved ductility of magnesium alloys by a simple shear process followed by annealing
Hua Zhang et al.
SCRIPTA MATERIALIA (2013)
Fatigue performance improvement in AISI 4140 steel by dynamic strain aging and dynamic precipitation during warm laser shock peening
Chang Ye et al.
ACTA MATERIALIA (2011)
Localized amorphism after high-strain-rate deformation in TWIP steel
N. Li et al.
ACTA MATERIALIA (2011)
Grain refinement mechanism of multiple laser shock processing impacts on ANSI 304 stainless steel
J. Z. Lu et al.
ACTA MATERIALIA (2010)
Grain refinement of LY2 aluminum alloy induced by ultra-high plastic strain during multiple laser shock processing impacts
J. Z. Lu et al.
ACTA MATERIALIA (2010)
The origin of rare earth texture development in extruded Mg-based alloys and its effect on tensile ductility
N. Stanford et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Dynamic recovery and recrystallization in titanium alloys by hot deformation
T. Furuhara et al.
JOM (2007)
Characterization of titanium alloy Ti-6Al-4V for chemical, marine and industrial applications
I Gurrappa
MATERIALS CHARACTERIZATION (2003)
Correlation of plastic deformation and dynamic recrystallization in magnesium alloy Zk60
A Galiyev et al.
ACTA MATERIALIA (2001)
Share Paper
