Related references
Note: Only part of the references are listed.Ad Hoc Heat Treatments for Selective Laser Melted Alsi10mg Alloy Aimed at Stress-Relieving and Enhancing Mechanical Performances
J. Fiocchi et al.
JOM (2020)
Alloying AlSi10Mg and Cu powders in laser Single Scan Tracks, melt spinning, and Laser Powder Bed Fusion
Silvia Marola et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2020)
Progress in additive manufacturing on new materials: A review
Neng Li et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)
3D printing of Aluminium alloys: Additive Manufacturing of Aluminium alloys using selective laser melting
Nesma T. Aboulkhair et al.
PROGRESS IN MATERIALS SCIENCE (2019)
A time-saving and cost-effective method to process alloys by Laser Powder Bed Fusion
Federico Bosio et al.
MATERIALS & DESIGN (2019)
Selective laser melted Al-7Si-0.6Mg alloy with in-situ precipitation via platform heating for residual strain removal
Jeremy H. Rao et al.
MATERIALS & DESIGN (2019)
Study of heat treatment parameters for additively manufactured AlSi10Mg in comparison with corresponding cast alloy
Luca Girelli et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
The Effect of Selective Laser Melting Process Parameters on the Microstructure and Mechanical Properties of A16061 and AlSi10Mg Alloys
Ahmed H. Maamoun et al.
MATERIALS (2019)
A comparison of Selective Laser Melting with bulk rapid solidification of AlSi10Mg alloy
Silvia Marola et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2018)
Microstructure, precipitates and hardness of selectively laser melted AlSi10Mg alloy before and after heat treatment
Le Zhou et al.
MATERIALS CHARACTERIZATION (2018)
Additive manufacturing of metallic components - Process, structure and properties
T. DebRoy et al.
PROGRESS IN MATERIALS SCIENCE (2018)
Effect of heat treatment on the microstructure and anisotropy in mechanical properties of A357 alloy produced by selective laser melting
Kun V. Yang et al.
MATERIALS & DESIGN (2018)
Effect of Selective Laser Melting Process Parameters on the Quality of Al Alloy Parts: Powder Characterization, Density, Surface Roughness, and Dimensional Accuracy
Ahmed H. Maamoun et al.
MATERIALS (2018)
Effects of Platform Pre-Heating and Thermal-Treatment Strategies on Properties of AlSi10Mg Alloy Processed by Selective Laser Melting
Riccardo Casati et al.
METALS (2018)
Low temperature annealing dedicated to AlSi10Mg selective laser melting products
J. Fiocchi et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2017)
Effect of Process and Post-Process Conditions on the Mechanical Properties of an A357 Alloy Produced via Laser Powder Bed Fusion
Alberta Aversa et al.
METALS (2017)
Additive manufacturing of metals
Dirk Herzog et al.
ACTA MATERIALIA (2016)
Effect of heat treatment on AlSi10Mg alloy fabricated by selective laser melting: Microstructure evolution, mechanical properties and fracture mechanism
Wei Li et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
The microstructure and mechanical properties of selectively laser melted AlSi10Mg: The effect of a conventional T6-like heat treatment
Nesma T. Aboulkhair et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
Selective laser melting of AlSi10Mg: Influence of post-processing on the microstructural and tensile properties development
U. Tradowsky et al.
MATERIALS & DESIGN (2016)
The influence of processing parameters on aluminium alloy A357 manufactured by Selective Laser Melting
Heng Rao et al.
MATERIALS & DESIGN (2016)
Microstructures and mechanical properties of A356 (AlSi7Mg0.3) aluminum alloy fabricated by selective laser melting
Takahiro Kimura et al.
MATERIALS & DESIGN (2016)
On the Precipitation Hardening of Selective Laser Melted AlSi10Mg
Nesma T. Aboulkhair et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2015)
Investigation on reducing distortion by preheating during manufacture of aluminum components using selective laser melting
Damien Buchbinder et al.
JOURNAL OF LASER APPLICATIONS (2014)
Design optimization of supports for overhanging structures in aluminum and titanium alloys by selective laser melting
F. Calignano
MATERIALS & DESIGN (2014)
Microstructure and mechanical properties of Al-12Si produced by selective laser melting: Effect of heat treatment
K. G. Prashanth et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder
Lore Thijs et al.
ACTA MATERIALIA (2013)
Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): Microstructure, high cycle fatigue, and fracture behavior
Erhard Brandl et al.
MATERIALS & DESIGN (2012)
Assessing and comparing influencing factors of residual stresses in selective laser melting using a novel analysis method
Jean-Pierre Kruth et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2012)
Investigations on residual stresses and deformations in selective laser melting
Michael F. Zaeh et al.
PRODUCTION ENGINEERING-RESEARCH AND DEVELOPMENT (2010)
Residual stresses in selective laser sintering and selective laser melting
Peter Mercelis et al.
RAPID PROTOTYPING JOURNAL (2006)
Share Paper
