Related references
Note: Only part of the references are listed.Neural network modeling for anisotropic mechanical properties and work hardening behavior of Inconel 718 alloy at elevated temperatures
Gauri Mahalle et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2019)
Analytical prediction of temperature in laser-assisted milling with laser preheating and machining effects
Yixuan Feng et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
One-Dimensional Heat Conduction Inverse Modelling of Heat Flux Generated at Tool-Chip Interface in Cutting Inconel 718
Jinfu Zhao et al.
IEEE ACCESS (2019)
Cutting temperature measurement using an improved two-color infrared thermometer in turning Inconel 718 with whisker-reinforced ceramic tools
Jinfu Zhao et al.
CERAMICS INTERNATIONAL (2018)
Investigation of tool wear in the turning of Inconel 718 superalloy in terms of process performance and productivity enhancement
W. Grzesik et al.
TRIBOLOGY INTERNATIONAL (2018)
Determining tool/chip temperatures from thermography measurements in metal cutting
M. Saez-de-Buruaga et al.
APPLIED THERMAL ENGINEERING (2018)
Investigation of Cutting Temperature during Turning Inconel 718 with (Ti,Al)N PVD Coated Cemented Carbide Tools
Jinfu Zhao et al.
MATERIALS (2018)
Mechanical characterization and modelling of Inconel 718 material behavior for machining process assessment
A. Iturbe et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Tool wear on nickel alloys with different coolant pressures: Comparison of Alloy 718 and Waspaloy
R. Polvorosa et al.
JOURNAL OF MANUFACTURING PROCESSES (2017)
Influence of High-Pressure Coolant Assistance on the Machinability of the Titanium Alloy Ti555-3
Tarek Braham-Bouchnak et al.
MACHINING SCIENCE AND TECHNOLOGY (2015)
Combined Effect of Aluminum Content and Layer Structure on the Oxidation Performance of Ti1-xAlxN Based Coatings
Jihua Peng et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2014)
Tool wear characteristics in machining of nickel-based superalloys
Dahu Zhu et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2013)
Cutting temperature prediction in high speed machining by numerical modelling of chip formation and its dependence with crater wear
G. List et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2012)
Dry machining of Inconel 718, workpiece surface integrity
A. Devillez et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2011)
Wear mechanisms of WC coated and uncoated tools in finish turning of Inconel 718
Abhay Bhatt et al.
TRIBOLOGY INTERNATIONAL (2010)
High temperature deformation of Inconel 718
A. Thomas et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2006)
Influence of cutting tool coatings on the tribological phenomena at the tool-chip interface in orthogonal dry turning
J Rech
SURFACE & COATINGS TECHNOLOGY (2006)
Heat generation and temperature prediction in metal cutting: A review and implications for high speed machining
N. A. Abukhshim et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2006)
Key improvements in the machining of difficult-to-cut aerospace superalloys
EO Ezugwu
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2005)
A review of developments towards dry and high speed machining of Inconel 718 alloy
D Dudzinski et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2004)
Investigation of the effects of tool micro-geometry and coating on tool temperature during orthogonal turning of quenched and tempered steel
R M'Saoubi et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2004)
Physics based modelling of interface temperatures in machining with multilayer coated tools at moderate cutting speeds
W Grzesik et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2004)
An overview of the machinability of aeroengine alloys
EO Ezugwu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)
Time resolved temperature measurements in manufacturing
B Muller et al.
MEASUREMENT (2003)
Modeling cutting temperatures for turning inserts with various tool geometries and materials
AU Anagonye et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2002)
Thermal modeling of the metal cutting process - Part III: temperature rise distribution due to the combined effects of shear plane heat source and the tool-chip interface frictional heat source
R Komanduri et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2001)
Comparison of filtered high-current pulsed arc deposition (φ-HCA) with conventional vacuum arc methods
T Witke et al.
SURFACE & COATINGS TECHNOLOGY (2000)
Share Paper
