Related references
Note: Only part of the references are listed.A probabilistic Kitagawa-Takahashi diagram for fatigue strength assessment of cast aluminium alloys
R. Aigner et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
On the Statistical Size Effect of Cast Aluminium
Roman Aigner et al.
MATERIALS (2019)
On the mean stress sensitivity of cast aluminium considering imperfections
R. Aigner et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
On the statistical distribution of primary and secondary dendrite arm spacing in cast metals
Murat Tiryakioglu
MATERIALS SCIENCE AND TECHNOLOGY (2019)
Short and Long Crack Growth of Aluminium Cast Alloys
Martin Leitner et al.
MECHANICAL FATIGUE OF METALS: EXPERIMENTAL AND SIMULATION PERSPECTIVES (2019)
Influence of secondary dendrite arm spacing (SDAS) on the fatigue properties of different conventional automotive aluminum cast alloys
Sascha Gerbe et al.
FRATTURA ED INTEGRITA STRUTTURALE-FRACTURE AND STRUCTURAL INTEGRITY (2019)
The cyclic R-curve - Determination, problems, limitations and application
Juergen Maierhofer et al.
ENGINEERING FRACTURE MECHANICS (2018)
Oxide induced crack closure in the near threshold regime: The effect of oxide debris release
J. Maierhofer et al.
INTERNATIONAL JOURNAL OF FATIGUE (2018)
Modification of a Defect-Based Fatigue Assessment Model for Al-Si-Cu Cast Alloys
Roman Aigner et al.
MATERIALS (2018)
Application of a √area-Approach for Fatigue Assessment of Cast Aluminum Alloys at Elevated Temperature
Roman Aigner et al.
METALS (2018)
The significance of microstructure heterogeneities on the fatigue thresholds of aluminum castings
Sascha Gerbe et al.
12TH INTERNATIONAL FATIGUE CONGRESS (FATIGUE 2018) (2018)
Fatigue crack closure: a review of the physical phenomena
R. Pippan et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2017)
Microstructural mechanisms and advanced characterization of long and small fatigue crack growth in cast A356-T61 aluminum alloys
Anthony G. Spangenberger et al.
INTERNATIONAL JOURNAL OF FATIGUE (2017)
Comparison of Measurement Methods for Secondary Dendrite Arm Spacing
Eli Vandersluis et al.
METALLOGRAPHY MICROSTRUCTURE AND ANALYSIS (2017)
About the fatigue crack propagation threshold of metals as a design criterion - A review
Uwe Zerbst et al.
ENGINEERING FRACTURE MECHANICS (2016)
Effect of load ratio on fatigue crack growth in the near-threshold regime: A literature review, and a combined crack closure and driving force approach
Ming-Liang Zhu et al.
ENGINEERING FRACTURE MECHANICS (2015)
Fracture mechanics based assessment of the fatigue strength: approach for the determination of the initial crack size
U. Zerbst et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2015)
Near-threshold behaviour of shear-mode fatigue cracks in metallic materials
J. Pokluda et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2014)
Modified NASGRO equation for physically short cracks
J. Maierhofer et al.
INTERNATIONAL JOURNAL OF FATIGUE (2014)
Material defects as the basis of fatigue design
Yukitaka Murakami
INTERNATIONAL JOURNAL OF FATIGUE (2012)
Curvature of micropores in Al-Cu alloys: An X-ray tomography study
M. Felberbaum et al.
ACTA MATERIALIA (2011)
Modelling of fatigue thresholds for small cracks in a mild steel by Strip-Yield model
S. Beretta et al.
ENGINEERING FRACTURE MECHANICS (2009)
Microstructure, tensile and fatigue properties of the Al-10%Si-2%Cu alloy with different Fe and Mn content cast under controlled conditions
Lorella Ceschini et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
Correlation between ultimate tensile strength and solidification microstructure for the sand cast A357 aluminium alloy
L. Ceschini et al.
MATERIALS & DESIGN (2009)
On the relationship between statistical distributions of defect size and fatigue life in 7050-T7451 thick plate and A356-T6 castings
Murat Tiryakioglu
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)
Relationship between Defect Size and Fatigue Life Distributions in Al-7 Pct Si-Mg Alloy Castings
Murat Tiryakioglu
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2009)
Effect of cooling rate on solidified microstructure and mechanical properties of aluminium-A356 alloy
L. Y. Zhang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Application of Taguchi's methods to investigate some factors affecting microporosity formation in A360 aluminium alloy casting
Oemer Savas et al.
MATERIALS & DESIGN (2007)
Fatigue crack growth mechanisms at the microstructure scale in Al-Si-Mg cast alloys: Mechanisms in regions II and III
Diana A. Lados et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2006)
Interactions of plasticity and oxide crack closure mechanisms near the fatigue crack growth threshold
JA Newman et al.
INTERNATIONAL JOURNAL OF FATIGUE (2004)
Fatigue propagation threshold of short cracks under constant amplitude loading
MD Chapetti
INTERNATIONAL JOURNAL OF FATIGUE (2003)
The effect of solidification time and heat treatment on the fatigue properties of a cast 319 aluminum alloy
JM Boileau et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2003)
On the √area relationship and the short fatigue crack threshold
AJ McEvily et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2003)
Determination of the length dependence of the threshold for fatigue crack propagation
B Tabernig et al.
ENGINEERING FRACTURE MECHANICS (2002)
Enhanced model of partial crack closure for correlation of R-ratio effects in aluminum alloys
D Kujawski
INTERNATIONAL JOURNAL OF FATIGUE (2001)
Share Paper
