Related references
Note: Only part of the references are listed.Material characterization of a pultrusion specific and highly reactive polyurethane resin system: Elastic modulus, rheology, and reaction kinetics
Onur Yuksel et al.
COMPOSITES PART B-ENGINEERING (2021)
Permeability and compaction behaviour of air-texturised glass fibre rovings: A characterisation study
Michael Sandberg et al.
JOURNAL OF COMPOSITE MATERIALS (2020)
In-plane permeability characterization of engineering textiles based on radial flow experiments: A benchmark exercise
D. May et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2019)
Simulation of liquid composite moulding using a finite volume scheme and the level-set method
Michael Sandberg et al.
INTERNATIONAL JOURNAL OF MULTIPHASE FLOW (2019)
Simulation of resin-impregnation, heat-transfer and cure in a resin-injection pultrusion process
Michael Sandberg et al.
PROCEEDINGS OF THE 22ND INTERNATIONAL ESAFORM CONFERENCE ON MATERIAL FORMING (ESAFORM 2019) (2019)
A Review on the Mechanical Modeling of Composite Manufacturing Processes
Ismet Baran et al.
ARCHIVES OF COMPUTATIONAL METHODS IN ENGINEERING (2017)
Simulating tape resin infiltration during thermoset pultrusion process
P. Simacek et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2015)
Modeling of heat transfer and unsaturated flow in woven fiber reinforcements during direct injection-pultrusion process of thermoplastic composites
Arthur Babeau et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2015)
Modelling the pultrusion process of an industrial L-shaped composite profile
Ismet Baran et al.
COMPOSITE STRUCTURES (2014)
Thermo-Chemical Modelling Strategies for the Pultrusion Process
Ismet Baran et al.
APPLIED COMPOSITE MATERIALS (2013)
Effect of Resin Viscosity in Fiber Reinforcement Compaction in Resin Injection Pultrusion Process
N. Shakya et al.
APPLIED COMPOSITE MATERIALS (2013)
Simulation of void formation in liquid composite molding processes
C. DeValve et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2013)
The effect of thermal contact resistance on the thermosetting pultrusion process
Ismet Baran et al.
COMPOSITES PART B-ENGINEERING (2013)
Process induced residual stresses and distortions in pultrusion
Ismet Baran et al.
COMPOSITES PART B-ENGINEERING (2013)
Characterization Methodology of Thermoset Resins for the Processing of Composite Materials - Case Study: CYCOM 890RTM Epoxy Resin
Lolei Khoun et al.
JOURNAL OF COMPOSITE MATERIALS (2010)
Iterative and transient numerical models for flow simulation of injection pultrusion
XL Liu
COMPOSITE STRUCTURES (2004)
Mathematical model for the pultrusion of blocked PU-UP matrix composites
CH Chen et al.
JOURNAL OF APPLIED POLYMER SCIENCE (2003)
Numerical simulation of pressure variation and resin flow in injection pultrusion
SS Rahatekar et al.
JOURNAL OF COMPOSITE MATERIALS (2003)
A fixed mesh numerical method for modelling the flow in liquid composites moulding processes using a volume of fluid technique
JA Garcia et al.
COMPUTER METHODS IN APPLIED MECHANICS AND ENGINEERING (2003)
The effect of anisotropic thermal conductivity on the pultrusion process simulation
AV Pantaleao et al.
INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER (2002)
Three-dimensional finite-element/nodal-control-volume simulation of the pultrusion process with temperature-dependent material properties including resin shrinkage
SC Joshi et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2001)
Numerical and experimental analysis of resin flow and cure in resin injection pultrusion (RIP)
ZM Ding et al.
POLYMER COMPOSITES (2000)
Share Paper
