Related references
Note: Only part of the references are listed.Multisyringe flow injection analysis (MSFIA) for the automatic determination of total iron in wines
Piyawan Phansi et al.
FOOD CHEMISTRY (2019)
Portable and selective colorimetric film and digital image colorimetry for detection of iron
Aree Choodum et al.
SPECTROCHIMICA ACTA PART A-MOLECULAR AND BIOMOLECULAR SPECTROSCOPY (2019)
PolyJet 3D-Printed Enclosed Microfluidic Channels without Photocurable Supports
Andre D. Castiaux et al.
ANALYTICAL CHEMISTRY (2019)
Three-Dimensional Printing of Abrasive, Hard, and Thermally Conductive Synthetic Microdiamond-Polymer Composite Using Low-Cost Fused Deposition Modeling Printer
Sidra Waheed et al.
ACS APPLIED MATERIALS & INTERFACES (2019)
Multimaterial 3D Printed Fluidic Device for Measuring Pharmaceuticals in Biological Fluids
Feng Li et al.
ANALYTICAL CHEMISTRY (2019)
Increasing the functionalities of 3D printed microchemical devices by single material, multimaterial, and print-pause-print 3D printing
Feng Li et al.
LAB ON A CHIP (2019)
Low-Cost Passive Sampling Device with Integrated Porous Membrane Produced Using Multimaterial 3D Printing
Umme Kalsoom et al.
ANALYTICAL CHEMISTRY (2018)
Custom 3D printer and resin for 18 μm x 20 μm microfluidic flow channels
Hua Gong et al.
LAB ON A CHIP (2017)
3D printed device including disk-based solid-phase extraction for the automated speciation of iron using the multisyringe flow injection analysis technique
Carlos Calderilla et al.
TALANTA (2017)
A Printed Equilibrium Dialysis Device with Integrated Membranes for Improved Binding Affinity Measurements
Cody W. Pinger et al.
ANALYTICAL CHEMISTRY (2017)
One-Step Fabrication of a Microfluidic Device with an Integrated Membrane and Embedded Reagents by Multimaterial 3D Printing
Feng Li et al.
ANALYTICAL CHEMISTRY (2017)
Comparing Microfluidic Performance of Three-Dimensional (3D) Printing Platforms
Niall P. Macdonald et al.
ANALYTICAL CHEMISTRY (2017)
Direct Production of Microstructured Surfaces for Planar Chromatography Using 3D Printing
Niall P. Macdonald et al.
ANALYTICAL CHEMISTRY (2017)
Nanoporous Membranes for Microfluidic Concentration Prior to Electrophoretic Separation of Proteins in Urine
Feng Li et al.
ANALYTICAL CHEMISTRY (2016)
3D-printed microfluidic devices: fabrication, advantages and limitations-a mini review
Chengpeng Chen et al.
ANALYTICAL METHODS (2016)
3D-Printed Microfluidics
Anthony K. Au et al.
ANGEWANDTE CHEMIE-INTERNATIONAL EDITION (2016)
3D printed microfluidic devices: enablers and barriers
Sidra Waheed et al.
LAB ON A CHIP (2016)
The upcoming 3D-printing revolution in microfluidics
Nirveek Bhattacharjee et al.
LAB ON A CHIP (2016)
3D printing: an emerging tool for novel microfluidics and lab-on-a-chip applications
Alireza Ahmadian Yazdi et al.
MICROFLUIDICS AND NANOFLUIDICS (2016)
Three-dimensional printing of continuous-fiber composites by in-nozzle impregnation
Ryosuke Matsuzaki et al.
SCIENTIFIC REPORTS (2016)
3D-printed microfluidic devices
Reza Amin et al.
BIOFABRICATION (2016)
3D printed microfluidics for biological applications
Chee Meng Benjamin Ho et al.
LAB ON A CHIP (2015)
Development of a portable setup and a multicommuted flow analysis procedure for the photometric determination of Fe(III) and Fe(II) in fresh water
Jeova C. Miranda et al.
SENSORS AND ACTUATORS B-CHEMICAL (2015)
Fundamental Studies of Nanofluidics: Nanopores, Nanochannels, and Nanopipets
Daniel G. Haywood et al.
ANALYTICAL CHEMISTRY (2015)
Cost-Effective Three-Dimensional Printing of Visibly Transparent Microchips within Minutes
Aliaa I. Shallan et al.
ANALYTICAL CHEMISTRY (2014)
Evaluation of 3D Printing and Its Potential Impact on Biotechnology and the Chemical Sciences
Bethany C. Gross et al.
ANALYTICAL CHEMISTRY (2014)
Bacterial siderophores efficiently provide iron to iron-starved tomato plants in hydroponics culture
W. Radzki et al.
ANTONIE VAN LEEUWENHOEK INTERNATIONAL JOURNAL OF GENERAL AND MOLECULAR MICROBIOLOGY (2013)
Lab-on-Paper with Dual Electrochemical/Colorimetric Detection for Simultaneous Determination of Gold and Iron
Amara Apilux et al.
ANALYTICAL CHEMISTRY (2010)
Separation, preconcentration and inductively coupled plasma-mass spectrometric (ICP-MS) determination of thorium(IV), titanium(IV), iron(III), lead(II) and chromium(III) on 2-nitroso-1-naphthol impregnated MCI GEL CHP20P resin
Funda Armagan Aydin et al.
JOURNAL OF HAZARDOUS MATERIALS (2010)
Self-sealed vertical polymeric nanoporous-junctions for high-throughput nanofluidic applications
Sung Jae Kim et al.
ANALYTICAL CHEMISTRY (2008)
Membranes and microfluidics: a review
J. de Jong et al.
LAB ON A CHIP (2006)
A novel method for the filterless preconcentration of iron
JET Andersen
ANALYST (2005)
Fe isotope variations in natural materials measured using high mass resolution multiple collector ICPMS
GL Arnold et al.
ANALYTICAL CHEMISTRY (2004)
High resolution sector field ICP-MS and multicollector ICP-MS as tools for trace metal speciation in environmental studies: a review
M Moldovan et al.
JOURNAL OF ANALYTICAL ATOMIC SPECTROMETRY (2004)
The accurate determination of the first row transition metals in water, urine, plant, tissue and rock samples by sector field ICP-MS
AT Townsend
JOURNAL OF ANALYTICAL ATOMIC SPECTROMETRY (2000)
Share Paper
