Related references
Note: Only part of the references are listed.Microstructure and stress corrosion cracking of a SA508-309L/308L-316L dissimilar metal weld joint in primary pressurized water reactor environment
Lijin Dong et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)
Metallurgical, Fatigue and Pitting Corrosion Behavior of AISI 316 Joints Welded with Nb-Based Stabilized Steel Filler
Dikshant Malhotra et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2020)
Corrosion resistance of welded joints of X5CrNi18-10 stainless steel
Bore Jegdic et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)
Improved corrosion resistance of 316LN stainless steel performed by rotationally accelerated shot peening
Xudong Chen et al.
APPLIED SURFACE SCIENCE (2019)
Pitting behavior of welded joint and the role of carbon ring in improving corrosion resistance
Tongjiao Chu et al.
MATERIALS & DESIGN (2019)
Effect of polishing process on corrosion behavior of 308L stainless steel in high temperature water
Cheng Ma et al.
APPLIED SURFACE SCIENCE (2018)
Microstructure and corrosion behavior of the heat affected zone of a stainless steel 308L-316L weld joint
Cheng Ma et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2018)
Local Electrochemistry and In Situ Microscopy of Pitting at Sensitized Grain Boundary of Type 304 Stainless Steel in NaCl Solution
Noriyuki Ida et al.
JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2017)
Influence of microstructure and elemental partitioning on pitting corrosion resistance of duplex stainless steel welding joints
Zhiqiang Zhang et al.
APPLIED SURFACE SCIENCE (2017)
Stress corrosion cracking in the heat affected zone of a stainless steel 308L-316L weld joint in primary water
Lijin Dong et al.
CORROSION SCIENCE (2016)
Short time oxidation behavior of 308L weld metal and 316L stainless steel with different surface state in simulated primary water with 0.1 mg/L dissolved oxygen
H. -L. Ming et al.
MATERIALS AND CORROSION-WERKSTOFFE UND KORROSION (2015)
Microstructural characterization of an SA508-309L/308L-316L domestic dissimilar metal welded safe-end joint
Hongliang Ming et al.
MATERIALS CHARACTERIZATION (2014)
Corrosion of low-temperature nitrided molybdenum-bearing stainless steels
M. Kuczynska-Wydorska et al.
CORROSION SCIENCE (2011)
Measurement of local plastic strain distribution of stainless steel by electron backscatter diffraction
Masayuki Kamaya
MATERIALS CHARACTERIZATION (2009)
Microstructure and pitting corrosion of similar and dissimilar stainless steel welds
G. M. Reddy et al.
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2008)
Influence of pH on the passivation behavior of 254SMO stainless steel in 3.5% NaCl solution
C. T. Liu et al.
CORROSION SCIENCE (2007)
The role of residual stress in neutral pH stress corrosion cracking of pipeline steels. Part 1: Pitting and cracking occurrence
G. Van Boven et al.
ACTA MATERIALIA (2007)
Crack trapping effect of persistent grain boundary islands
X Kong et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2005)
Evaluation of initial corrosion location in E316L austenitic stainless steel weld metals
Y Cui et al.
MATERIALS LETTERS (2005)
Effect of heat treatment on the precipitation and pitting corrosion behavior of 347 SS weld overlay
IH Lo et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)
The inhibition of pitting corrosion of stainless steels by chromate and molybdate ions
GO Ilevbare et al.
CORROSION SCIENCE (2003)
Share Paper
