Related references
Note: Only part of the references are listed.Effects of nozzle and fluid properties on the drop formation dynamics in a drop-on-demand inkjet printing
A. B. Aqeel et al.
APPLIED MATHEMATICS AND MECHANICS-ENGLISH EDITION (2019)
Controllable printing droplets on demand by piezoelectric inkjet: applications and methods
Kai Li et al.
MICROSYSTEM TECHNOLOGIES-MICRO-AND NANOSYSTEMS-INFORMATION STORAGE AND PROCESSING SYSTEMS (2018)
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Tuan D. Ngo et al.
COMPOSITES PART B-ENGINEERING (2018)
Analysis of droplet stability after ejection from an inkjet nozzle
Yonghong Zhong et al.
JOURNAL OF FLUID MECHANICS (2018)
Droplet formation at megahertz frequency
John C. Miers et al.
AICHE JOURNAL (2017)
Research on mechanism of generating aluminum droplets smaller than the nozzle diameter by pneumatic drop-on-demand technology
Song-Yi Zhong et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
A waveform design method for high DPI piezoelectric inkjet print-head based on numerical simulation
Hongfang Wei et al.
MICROSYSTEM TECHNOLOGIES-MICRO-AND NANOSYSTEMS-INFORMATION STORAGE AND PROCESSING SYSTEMS (2017)
Comprehensive examination of a new mechanism to produce small droplets in drop-on-demand inkjet technology
Sadegh Poozesh et al.
APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2016)
Jetting Frequency and Evaporation Effects on the Measurement Accuracy of Inkjet Droplet Amount
Kye-Si Kwon et al.
JOURNAL OF IMAGING SCIENCE AND TECHNOLOGY (2015)
Dynamic nozzles for drop generators
J. R. Castrejon-Pita et al.
REVIEW OF SCIENTIFIC INSTRUMENTS (2015)
A review on powder-based additive manufacturing for tissue engineering: selective laser sintering and inkjet 3D printing
Seyed Farid Seyed Shirazi et al.
SCIENCE AND TECHNOLOGY OF ADVANCED MATERIALS (2015)
Numerical study on the effects of non-dimensional parameters on drop-on-demand droplet formation dynamics and printability range in the up-scaled model
Eunjeong Kim et al.
PHYSICS OF FLUIDS (2012)
A novel method to produce small droplets from large nozzles
A. A. Castrejon-Pita et al.
REVIEW OF SCIENTIFIC INSTRUMENTS (2012)
Experiments and Lagrangian simulations on the formation of droplets in drop-on-demand mode
J. R. Castrejon-Pita et al.
PHYSICAL REVIEW E (2011)
Wolfgang von Ohnesorge
Gareth H. McKinley et al.
PHYSICS OF FLUIDS (2011)
Generation and breakup of Worthington jets after cavity collapse. Part 1. Jet formation
Stephan Gekle et al.
JOURNAL OF FLUID MECHANICS (2010)
Generation and breakup of Worthington jets after cavity collapse. Part 2. Tip breakup of stretched jets
J. M. Gordillo et al.
JOURNAL OF FLUID MECHANICS (2010)
Experimental analysis of waveform effects on satellite and ligament behavior via in situ measurement of the drop-on-demand drop formation curve and the instantaneous jetting speed curve
Kye-Si Kwon
JOURNAL OF MICROMECHANICS AND MICROENGINEERING (2010)
Effects of Actuating Pressure Waveforms on the Droplet Behavior in a Piezoelectric Inkjet
Hsuan-Chung Wu et al.
MATERIALS TRANSACTIONS (2010)
Formation of beads-on-a-string structures during break-up of viscoelastic filaments
Pradeep P. Bhat et al.
NATURE PHYSICS (2010)
The dynamics of the piezo inkjet printhead operation
Herman Wijshoff
PHYSICS REPORTS-REVIEW SECTION OF PHYSICS LETTERS (2010)
Waveform Design Methods for Piezo Inkjet Dispensers Based on Measured Meniscus Motion
Kye-Si Kwon
JOURNAL OF MICROELECTROMECHANICAL SYSTEMS (2009)
Reduction of droplet volume by controlling actuating waveforms in inkjet printing for micro-pattern formation
H. Y. Gan et al.
JOURNAL OF MICROMECHANICS AND MICROENGINEERING (2009)
A new method for significantly reducing drop radius without reducing nozzle radius in drop-on-demand drop production
AU Chen et al.
PHYSICS OF FLUIDS (2002)
Share Paper
