Related references
Note: Only part of the references are listed.Gas entrainment behavior of aluminum alloy engine crankcases during the low-pressure-die-casting process
Jingying Sun et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)
Mechanical and material properties of castings produced via 3D printed molds
Dean A. Snelling et al.
ADDITIVE MANUFACTURING (2019)
3D printing of ceramics: A review
Zhangwei Chen et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)
Three-dimensional evaluations of the digital casts of morphologic maxillary teeth symmetry in patients with unilateral palatally displaced canines
Rosalia Leonardi et al.
AMERICAN JOURNAL OF ORTHODONTICS AND DENTOFACIAL ORTHOPEDICS (2019)
Novel sprue designs in metal casting via 3D sand-printing
Santosh Reddy Sama et al.
ADDITIVE MANUFACTURING (2019)
Experimental and numerical study of section restriction effects on filling behavior in low-pressure aluminum casting
A. Sanitas et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)
Simulation of Air Entrainment during Mold Filling: Comparison with Water Modeling Experiments
Seyyed Hojjat Majidi et al.
METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE (2018)
Non-conventional mold design for metal casting using 3D sand-printing
Santosh Reddy Sama et al.
JOURNAL OF MANUFACTURING PROCESSES (2018)
Additive manufacturing-driven mold design for castings
Jinwu Kang et al.
ADDITIVE MANUFACTURING (2018)
Modeling of the chemical finishing process for polylactic acid parts in fused deposition modeling and investigation of its tensile properties
Yifan Jin et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
3D-printed shell-truss sand mold for aluminum castings
Haolong Shangguan et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
3D printing for rapid sand casting-A review
Meet Upadhyay et al.
JOURNAL OF MANUFACTURING PROCESSES (2017)
QUANTIFYING THE ROLE OF PART DESIGN COMPLEXITY IN USING 3D SAND PRINTING FOR MOLDS AND CORES
Eyad S. Almaghariz et al.
INTERNATIONAL JOURNAL OF METALCASTING (2016)
Study of Refinement and Morphology Change of AlFeSi Phase in A380 Alloy due to Addition of Ca, Sr/ Ca, Mn and Mn, Sr
Meng Wang et al.
MATERIALS TRANSACTIONS (2016)
Additive Manufacture of Ceramics Components by Inkjet Printing
Brian Derby
ENGINEERING (2015)
On the conjoint influence of heat treatment and lithium content on microstructure and mechanical properties of A380 aluminum alloy
Mostafa Karamouz et al.
MATERIALS & DESIGN (2014)
Effect of oxide bifilms on the mechanical properties of cast Al-7Si-0.3Mg alloy and the roll of runner height after filter on their formation
Ghasem Eisaabadi Bozchaloei et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Experimental study aiming to enhance the surface finish of fused deposition modeled parts
L. M. Galantucci et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2009)
A multiple-gate runner system for gravity casting
Fu-Yuan Hsu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
Direct metal rapid casting: mechanical optimization and tolerance calculation
Elena Bassoli et al.
RAPID PROTOTYPING JOURNAL (2009)
The influence of porosity on the fatigue life for sand and permanent mould cast aluminium
Jan Linder et al.
INTERNATIONAL JOURNAL OF FATIGUE (2006)
An overview of the effects of bifilms on the structure and properties of cast alloys
John Campbell
METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE (2006)
Optimal design of gating systems by gradient search methods
Carlos E. Esparza et al.
COMPUTATIONAL MATERIALS SCIENCE (2006)
Effects of runner system design on the mechanical strength of Al-7Si-Mg alloy castings
X Dai et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)
Flow modelling in casting processes
P Cleary et al.
APPLIED MATHEMATICAL MODELLING (2002)