Related references
Note: Only part of the references are listed.Effects of laser shock peening on microstructure and fatigue behavior of Ti-6Al-4V alloy fabricated via electron beam melting
Xinyuan Jin et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)
Microstructural evolution and stress state related to mechanical properties of electron beam melted Ti-6Al-4V alloy modified by laser shock peening
Liang Lan et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)
Laser shock peening: A promising tool for tailoring metallic microstructures in selective laser melting
N. Kalentics et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)
Microscale residual stresses in additively manufactured stainless steel
Wen Chen et al.
NATURE COMMUNICATIONS (2019)
Additive manufacturing of ultrafine-grained high-strength titanium alloys
Duyao Zhang et al.
NATURE (2019)
Additively manufactured hierarchical stainless steels with high strength and ductility
Y. Morris Wang et al.
NATURE MATERIALS (2018)
Microstructure, residual stress and tensile properties control of wire-arc additive manufactured 2319 aluminum alloy with laser shock peening
Rujian Sun et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2018)
Ultrastrong nanocrystalline stainless steel and its Hall-Petch relationship in the nanoscale
Fei Yin et al.
SCRIPTA MATERIALIA (2018)
Laser shock peening of laser additive manufactured Ti6Al4V titanium alloy
Wei Guo et al.
SURFACE & COATINGS TECHNOLOGY (2018)
Effect of laser shock peening on microstructure and hot corrosion of TC11 alloy
Zhaopeng Tong et al.
SURFACE & COATINGS TECHNOLOGY (2018)
Selective Laser Melting Produced Ti-6Al-4V: Post-Process Heat Treatments to Achieve Superior Tensile Properties
Gerrit M. Ter Haar et al.
MATERIALS (2018)
Defects-dictated tensile properties of selective laser melted Ti-6Al-4V
Thomas Voisin et al.
MATERIALS & DESIGN (2018)
Microstructure characteristics and formation mechanism of TC17 titanium alloy induced by laser shock processing
Yang Yang et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2017)
Structural components manufactured by Selective Laser Melting and Investment Casting-Impact of the process route on the damage mechanism under cyclic loading
S. Leuders et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Influence of Transformation Plasticity on the Distribution of Internal Stress in Three Water-Quenched Cylinders
Yu Liu et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2017)
3D Laser Shock Peening - A new method for the 3D control of residual stresses in Selective Laser Melting
Nikola Kalentics et al.
MATERIALS & DESIGN (2017)
Additive manufacturing and postprocessing of Ti-6Al-4V for superior mechanical properties
M. Qian et al.
MRS BULLETIN (2016)
[INVITED] A review: Warm laser shock peening and related laser processing technique
Yiliang Liao et al.
OPTICS AND LASER TECHNOLOGY (2016)
High strength and high ductility behavior of 6061-T6 alloy after laser shock processing
Simge Gencalp Irizalp et al.
OPTICS AND LASERS IN ENGINEERING (2016)
Formation and control of martensite in Ti-6Al-4V alloy produced by selective laser melting
Jingjing Yang et al.
MATERIALS & DESIGN (2016)
Effect of laser shock peening on the mechanical properties of a near-α titanium alloy
Weiju Jia et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Microstructure and residual stress improvement in wire and arc additively manufactured parts through high-pressure rolling
Paul A. Colegrove et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2013)
Heat treatment of Ti6Al4V produced by Selective Laser Melting: Microstructure and mechanical properties
Bey Vrancken et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2012)
Grain Refinement and Hardness Increase of Titanium via Trace Element Addition
J. -M. Oh et al.
MATERIALS TRANSACTIONS (2010)
Deformation Modes in Stainless Steel During Laser Shock Peening
Xiangqun Zhu et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2009)
Interrogations on the sub-surface strain hardening of grit blasted Ti-6Al-4V alloy
M. Multigner et al.
SURFACE & COATINGS TECHNOLOGY (2009)
Analysis of the different slip systems activated by tension in a α/β titanium alloy in relation with local crystallographic orientation
F Bridier et al.
ACTA MATERIALIA (2005)
Grain refinement strengthening of a micro-crystalline high nitrogen austenitic stainless steel
A Di Schino et al.
MATERIALS LETTERS (2003)
The onset of twinning in metals:: A constitutive description
MA Meyers et al.
ACTA MATERIALIA (2001)
Deformation mechanisms of Ti-6Al-4V alloy with a martensitic microstructure subjected to oligocyclic fatigue
JM Manero et al.
ACTA MATERIALIA (2000)
Share Paper
