Related references
Note: Only part of the references are listed.Comment on 'Adiabatic shear instability is not necessary for adhesion in cold spray'
H. Assadi et al.
SCRIPTA MATERIALIA (2019)
Achieving strength-ductility synergy in cold spray additively manufactured Al/B4C composites through a hybrid post-deposition treatment
Naeem Ul Haq Tariq et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)
Elucidation of cold-spray deposition mechanism by auger electron spectroscopic evaluation of bonding interface oxide film
Yuji Ichikawa et al.
ACTA MATERIALIA (2019)
Corrosion resistant nickel coating with strong adhesion on AZ31B magnesium alloy prepared by an in-situ shot-peening-assisted cold spray
Ying-Kang Wei et al.
CORROSION SCIENCE (2018)
A new approach to prepare fully dense Cu with high conductivities and anti-corrosion performance by cold spray
Yu-Juan Li et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2018)
Solid-state additive manufacturing and repairing by cold spraying: A review
Wenya Li et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2018)
Characterizations and anisotropy of cold-spraying additive-manufactured copper bulk
Kang Yang et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2018)
Room-temperature Au-Au bonding in atmospheric air using direct transferred atomically smooth Au film on electroplated patterns
Yuichi Kurashima et al.
MICROELECTRONIC ENGINEERING (2018)
Deposition behavior, microstructure and mechanical properties of an in-situ micro-forging assisted cold spray enabled additively manufactured Inconel 718 alloy
Xiao-Tao Luo et al.
MATERIALS & DESIGN (2018)
In-situ formation of Ni-Al intermetallics-coated graphite/Al composite in a cold-sprayed coating and its high temperature tribological behaviors
Chunjie Huang et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2017)
Influence of coating defects on the corrosion behavior of cold sprayed refractory metals
S. Kumar et al.
APPLIED SURFACE SCIENCE (2017)
New insights into the coating/substrate interfacial bonding mechanism in cold spray
Yingchun Xie et al.
SCRIPTA MATERIALIA (2016)
Detection of oxygen at the interface and its effect on strain, stress, and temperature at the interface between cold sprayed aluminum and steel substrate
KeeHyun Kim et al.
APPLIED SURFACE SCIENCE (2015)
Pretreatment effect of Cu feedstock on cold-sprayed coatings
K. H. Ko et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2014)
Measurement of the thermal conductivity of cold gas dynamically sprayed alumina-reinforced aluminum coatings between -150 °C and +200 °C. New test method and experimental results
Efim Litovsky et al.
SURFACE & COATINGS TECHNOLOGY (2014)
Deformation behavior of the oxide film on the surface of cold sprayed powder particle
Shuo Yin et al.
APPLIED SURFACE SCIENCE (2012)
Stress evolution and cracking of crystalline diamond thin films on ductile titanium substrate: Analysis by micro-Raman spectroscopy and analytical modelling
F. Ahmed et al.
ACTA MATERIALIA (2011)
Significant influence of particle surface oxidation on deposition efficiency, interface microstructure and adhesive strength of cold-sprayed copper coatings
Wen-Ya Li et al.
APPLIED SURFACE SCIENCE (2010)
Some aspects on 3D numerical modeling of high velocity impact of particles in cold spraying by explicit finite element analysis
Wen-Ya Li et al.
APPLIED SURFACE SCIENCE (2009)
The rebound phenomenon in kinetic spraying deposition
JW Wu et al.
SCRIPTA MATERIALIA (2006)
Modeling of oxidation-induced growth stresses
AM Limarga et al.
SCRIPTA MATERIALIA (2004)
Room temperature Cu-Cu direct bonding using surface activated bonding method
TH Kim et al.
JOURNAL OF VACUUM SCIENCE & TECHNOLOGY A (2003)
Cracking behaviour of PVD tungsten coatings deposited on steel substrates
T Ganne et al.
ACTA MATERIALIA (2002)
Share Paper
