Related references
Note: Only part of the references are listed.Comprehensive investigation of cutting mechanisms and hole quality in dry drilling woven aramid fibre-reinforced plastic with typical tools
Sinan Liu et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2019)
Formation mechanism of burr defect in aramid fiber composites based on fly-cutting test
Yong-Jie Bao et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Hole-making processes and their impacts on the microstructure and fatigue response of aircraft alloys
Dan Sun et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Effects of cooling position on tool wear reduction of secondary cutting edge corner of one-shot drill bit in drilling CFRP
Fuji Wang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Experimental analysis of drilling induced damage in aramid composites
A. Diaz-Alvarez et al.
COMPOSITE STRUCTURES (2018)
Study on chisel edge drilling behavior and step drill structure on delamination in drilling CFRP
Xinyi Qiu et al.
COMPOSITE STRUCTURES (2018)
Investigation of hole quality during drilling of KFRP based on the interaction between collars and cutter
Sinan Liu et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Study on burr occurrence and surface integrity during slot milling of multidirectional and plain woven CFRPs
Maojun Li et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Drilling analysis of thin woven glass-fiber reinforced epoxy composites
U. A. Khashaba et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Mechanistic cutting force modelling for micro-drilling of CFRP composite laminates
Ravi Shankar Anand et al.
CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2017)
An energy based force prediction method for UD-CFRP orthogonal machining
Hao Li et al.
COMPOSITE STRUCTURES (2017)
Experimental study of coated tools effects in dry cutting of natural fiber reinforced plastics
Faissal Chegdani et al.
SURFACE & COATINGS TECHNOLOGY (2015)
A comparative evaluation of polycrystalline diamond drills in drilling high-strength T800S/250F CFRP
Jinyang Xu et al.
COMPOSITE STRUCTURES (2014)
Mechanistic modeling of oblique cutting considering fracture toughness and thermo-mechanical properties
Chang Liu et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2014)
Mechanical load distribution along the main cutting edges in drilling
Mihai-Bogdan Lazar et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2013)
Machinability analysis in drilling woven GFR/epoxy composites: Part II - Effect of drill wear
U. A. Khashaba et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2010)
Prediction of thrust force of step drill in drilling composite material by Taguchi method and radial basis function network
C. C. Tsao
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2008)
Drilling of carbon composites using a one shot drill bit. Part II: empirical modeling of maximum thrust force
M Fernandes et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2006)
Characterization of three-dimensional braided carbon/Kevlar hybrid composites for orthopedic usage
YZ Wan et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2005)
Dynamics of initial penetration in drilling: Part 1 - Mechanistic model for dynamic forces
YP Gong et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2005)
Factors affecting the machinability of GFR/epoxy composites
I El-Sonbaty et al.
COMPOSITE STRUCTURES (2004)
Share Paper
