Related references
Note: Only part of the references are listed.Effect of methane augmentation on combustion stability and unregulated emissions in compression ignition engine
Gaurav Tripathi et al.
FUEL (2020)
Comparisons of advanced combustion technologies (HCCI, PCCI, and dual-fuel PCCI) on engine performance and emission characteristics in a heavy-duty diesel engine
Euijoon Shim et al.
FUEL (2020)
Evaluation of a distributed combustion concept using 1-D modeling for pressurized oxy-combustion system with low flue gas recirculation
Hamed Jafari et al.
FUEL (2020)
Wet ethanol in LTC: How water fraction and DTBP affect combustion and intake temperature at naturally aspirated and boosted conditions
James Gohn et al.
FUEL (2020)
The comparison of combustion, engine performance and emission characteristics of ethanol, methanol, fusel oil, butanol, isopropanol and naphtha with n-heptane blends on HCCI engine
Alper Calam et al.
FUEL (2020)
Experimental investigation of pilot-fuel combustion in dual-fuel engines, Part 1: Thermodynamic analysis of combustion phenomena
Ales Srna et al.
FUEL (2019)
Experimental investigation of pilot-fuel combustion in dual-fuel engines, Part 2: Understanding the underlying mechanisms by means of optical diagnostics
Ales Srna et al.
FUEL (2019)
Ignition control in a gasoline compression ignition engine with ozone addition combined with a two-stage direct-injection strategy
Y. Kobashi et al.
FUEL (2019)
Effect of excess air/fuel ratio and methanol addition on the performance, emissions, and combustion characteristics of a natural gas/methanol dualfuel engine
Long Wang et al.
FUEL (2019)
Effect of diesel injection timing on the combustion of natural gas/diesel dual-fuel engine at low-high load and low-high speed conditions
Amin Yousefi et al.
FUEL (2019)
Benefits of E85 versus gasoline as low reactivity fuel for an automotive diesel engine operating in reactivity controlled compression ignition combustion mode
Jesus Benajes et al.
ENERGY CONVERSION AND MANAGEMENT (2018)
Parametric study and optimization of the main engine calibration parameters and compression ratio of a methane-diesel dual fuel engine
Giacomo Belgiorno et al.
FUEL (2018)
Performance and emissions of diesel-gasoline-ethanol blends in a light duty compression ignition engine
Giacomo Belgiorno et al.
FUEL (2018)
Effects on performances, emissions and particle size distributions of a dual fuel (methane-diesel) light-duty engine varying the compression ratio
G. Di Blasio et al.
APPLIED ENERGY (2017)
Influence of fuel properties on fundamental spray characteristics and soot emissions using different tailor-made fuels from biomass
Antonio Garcia et al.
ENERGY CONVERSION AND MANAGEMENT (2016)
ONE-DIMENSIONAL DIESEL SPRAY MODELING OF MULTICOMPONENT FUELS
J. V. Pastor et al.
ATOMIZATION AND SPRAYS (2015)
Effects of direct injection timing and blending ratio on RCCI combustion with different low reactivity fuels
Jesus Benajes et al.
ENERGY CONVERSION AND MANAGEMENT (2015)
The potential of RCCI concept to meet EURO VI NOx limitation and ultra-low soot emissions in a heavy-duty engine over the whole engine map
Jesus Benajes et al.
FUEL (2015)
Experimental Evaluation of Compression Ratio Influence on the Performance of a Dual-Fuel Methane-Diesel Light-Duty Engine
Gabriele Di Blasio et al.
SAE INTERNATIONAL JOURNAL OF ENGINES (2015)
Effects of pilot injection timing on the combustion and emissions characteristics in a diesel engine using biodiesel-CNG dual fuel
Kyunghyun Ryu
APPLIED ENERGY (2013)
ANALYSIS OF TRANSIENT LIQUID AND VAPOR PHASE PENETRATION FOR DIESEL SPRAYS UNDER VARIABLE INJECTION CONDITIONS
Jose V. Pastor et al.
ATOMIZATION AND SPRAYS (2011)
A 1D model for the description of mixing-controlled reacting diesel sprays
J. M. Desantes et al.
COMBUSTION AND FLAME (2009)
A 1D model for the description of mixing-controlled inert diesel sprays
Jose V. Pastor et al.
FUEL (2008)
Experimental investigation concerning the effect of natural gas percentage on performance and emissions of a DI dual fuel diesel engine
RG Papagiannakis et al.
APPLIED THERMAL ENGINEERING (2003)
Share Paper
