Related references
Note: Only part of the references are listed.Diagnosis of the microstructural and mechanical properties of over century-old steel railway bridge components
Maciej Kowal et al.
ENGINEERING FAILURE ANALYSIS (2020)
Physical Modeling of Cross Wedge Rolling Limitations
Lukasz Wojcik et al.
MATERIALS (2020)
The Abrasive Wear Resistance of Coatings Manufactured on High-Strength Low-Alloy (HSLA) Offshore Steel in Wet Welding Conditions
Jacek Tomkow et al.
COATINGS (2020)
Numerical Analysis of a Six Stage Forging Process for Producing Hollow Flanged Parts from Tubular Blanks
Grzegorz Winiarski et al.
ADVANCES IN SCIENCE AND TECHNOLOGY-RESEARCH JOURNAL (2020)
Strain hardening analysis and modelling of its parameters for sintered Al and Al-1%C preforms during cold upsetting
Rajeshkannan Ananthanarayanan et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2019)
Formability Limits, Fractography and Fracture Toughness in Sheet Metal Forming
Joao P. Magrinho et al.
MATERIALS (2019)
Corrosion Behavior of Annealed Steels with Different Carbon Contents (0.002, 0.17, 0.43 and 0.7% C) in Freely Aerated 3.5% NaCl Solution
Prvan Kumar Katiyar et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2019)
Grain Size Effect on the Mechanical Behavior of Metastable Fe-23Cr-8.5Ni Alloy
Lin Xie et al.
METALS (2019)
Effect of Substrate Roughness on Oxidation Resistance of an Aluminized Ni-Base Superalloy
Wojciech J. Nowak et al.
METALS (2019)
Continuous Cooling Transformation Diagram, Microstructures, and Properties of the Simulated Coarse-Grain Heat-Affected Zone in a Low-Carbon Bainite E550 Steel
Yun Zong et al.
METALS (2019)
Effect of austempering conditions on the microstructure and mechanical properties of AISI 4340 and AISI 4140 steels
Mian Muhammad Bilal et al.
Journal of Materials Research and Technology-JMR&T (2019)
Post-failure fracture surface analysis of notched steel specimens after bending-torsion fatigue
Wojciech Macek
ENGINEERING FAILURE ANALYSIS (2019)
Shot peening intensity effect on bending fatigue strength of S235, S355 and P460 structural steels
W. Macek et al.
IV INTERNATIONAL CONFERENCE OF COMPUTATIONAL METHODS IN ENGINEERING SCIENCE (CMES'19) (2019)
Effect of Tool Kinematics on Tube Flanging by Extrusion with a Moving Sleeve
Grzegorz Winiarski et al.
ADVANCES IN SCIENCE AND TECHNOLOGY-RESEARCH JOURNAL (2019)
Abrasion Resistance of S235, S355, C45, AISI 304 and Hardox 500 Steels with Usage of Garnet, Corundum and Carborundum Abrasives
Miroslaw Szala et al.
ADVANCES IN SCIENCE AND TECHNOLOGY-RESEARCH JOURNAL (2019)
Strain-induced martensite reversion in 18Cr-8Ni steel - transmission Kikuchi diffraction study
G. Cios et al.
MATERIALS SCIENCE AND TECHNOLOGY (2018)
Effect of Tempering Temperature on the Low Temperature Impact Toughness of 42CrMo4-V Steel
Chen Sun et al.
METALS (2018)
Microstructural Evolution during Severe Plastic Deformation by Gradation Extrusion
Philipp Frint et al.
METALS (2018)
Compositional analysis on the reverted austenite and tempered martensite in a Ti-stabilized supermartensitic stainless steel: Segregation, partitioning and carbide precipitation
J. D. Escobar et al.
MATERIALS & DESIGN (2018)
A study of a new screw press forging process for producing aircraft drop forgings made of magnesium alloy AZ61A
Andrzej Gontarz et al.
AIRCRAFT ENGINEERING AND AEROSPACE TECHNOLOGY (2018)
Monitoring Heat Treatments in Steels by a Non Destructive Ultrasonic Method
Linton Carvajal et al.
MATERIALS RESEARCH-IBERO-AMERICAN JOURNAL OF MATERIALS (2017)
Ratcheting fatigue behaviour of 42CrMo4 steel under different heat treatment conditions
R. Kreethi et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Fatigue Crack Growth Behavior of Austempered AISI 4140 Steel with Dissolved Hydrogen
Varun Ramasagara Nagarajan et al.
METALS (2017)
Studies on formability of sintered aluminum composites during hot deformation using strain hardening parameters
Sumesh Narayan et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2017)
MICROSTRUCTURAL CHARACTERISATION OF Co-Cr-Mo CASTING DENTAL ALLOYS
Miroslaw Szala et al.
ADVANCES IN SCIENCE AND TECHNOLOGY-RESEARCH JOURNAL (2017)
The influence of tool geometry on the course of flanges radial extrusion in hollow parts
Grzegorz Winiarski et al.
ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2017)
SIMULATION OF HELICAL GEAR FORMING OF AZ31 MAGNESIUM MATERIAL
Onder Ayer
ADVANCES IN SCIENCE AND TECHNOLOGY-RESEARCH JOURNAL (2017)
Description of full-range strain hardening behavior of steels
Tao Li et al.
SPRINGERPLUS (2016)
Plastometric tests for plasticine as physical modelling material
Lukasz Wojcik et al.
OPEN ENGINEERING (2016)
A THEORETICAL AND EXPERIMENTAL STUDY FOR THE LOAD OPTIMIZATION OF GEAR-LIKE PROFILES BY USING FORWARD AND LATERAL EXTRUSION
Tahir Altinbalik et al.
TRANSACTIONS OF THE CANADIAN SOCIETY FOR MECHANICAL ENGINEERING (2015)
Dependence of grain size on mechanical properties and microstructures of high manganese austenitic steel
Xiaoyun Yuan et al.
11TH INTERNATIONAL CONFERENCE ON TECHNOLOGY OF PLASTICITY, ICTP 2014 (2014)
Structural and Wear Characterization of Heat Treated En24 Steel
Rajesh K. Khatirkar et al.
ISIJ INTERNATIONAL (2012)
Finite Element simulation coupled to optimisation stochastic process to assess the effect of heat treatment on the mechanical properties of 42CrMo4 steel
D. Chaouch et al.
MATERIALS & DESIGN (2012)
XRD peak broadening characterization of deformed microstructures and heterogeneous behavior of carbon steel
M. Bouras et al.
THEORETICAL AND APPLIED FRACTURE MECHANICS (2012)
Strain Hardening Behaviour in Forming of Sintered Iron-0.35% Carbon Powder Metallurgy Preform During Cold Upsetting
Sumesh Narayan et al.
MATERIALS RESEARCH-IBERO-AMERICAN JOURNAL OF MATERIALS (2011)
An investigation on the microstructure and mechanical properties of direct-quenched and tempered AISI 4140 steel
A. H. Meysami et al.
MATERIALS & DESIGN (2010)
Influence of different initial microstructure on the process of spheroidization in cold forging
Erdal Karadeniz
MATERIALS & DESIGN (2008)
Strain hardening behaviour and temperature effect on Al-2124/SiCp
E Martín et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)