Related references
Note: Only part of the references are listed.Quantitative approach to realization of ultrasonic grain refinement of Al-7Si-2Cu-1Mg alloy
Soo-Bae Kim et al.
SCIENTIFIC REPORTS (2019)
Combined Effects of Ultrasonic Melt Treatment and Cu/Mg Solute on the Microstructure and Mechanical Properties of a Hypoeutectic Al-7Si Alloy
Soo-Bae Kim et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2019)
Influences of different Zr additions on the microstructure, room and high temperature mechanical properties of an Al-7Si-0.4Mg alloy modified with 0.25%Er
Marco Colombo et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Microstructure-Strengthening Interrelationship of an Ultrasonically Treated Hypereutectic Al-Si (A390) Alloy
Soo-Bae Kim et al.
METALS AND MATERIALS INTERNATIONAL (2018)
Microstructure and grain refining efficiency of Al-5Ti-1B master alloys prepared by halide salt route
Lili Zhang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Role of ultrasonic treatment, inoculation and solute in the grain refinement of commercial purity aluminium
G. Wang et al.
SCIENTIFIC REPORTS (2017)
Particle-induced morphological modification of Al alloy equiaxed dendrites revealed by sub-second in situ microtomography
R. Daudin et al.
ACTA MATERIALIA (2017)
Microstructure, tensile properties and fracture behavior of high temperature Al-Si-Mg-Cu cast alloys
A. M. A. Mohamed et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
Alloy Composition and Dendrite Arm Spacing in Al-Si-Cu-Mg-Fe Alloys
Tharmalingam Sivarupan et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2013)
Influence of ultrasonic melt treatment on microstructure and mechanical properties of AlSi9Cu3 alloy
H. Puga et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2011)
Influence of ultrasonic melt treatment on the formation of primary intermetallics and related grain refinement in aluminum alloys
L. Zhang et al.
JOURNAL OF MATERIALS SCIENCE (2011)
Characterization of tensile fracture in heavily alloyed Al-Si piston alloy
Guo-hua Zhang et al.
PROGRESS IN NATURAL SCIENCE-MATERIALS INTERNATIONAL (2011)
The heat treatment of Al-Si-Cu-Mg casting alloys
Emma Sjolander et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2010)
Optimisation of solution treatment of cast Al-Si-Cu alloys
E. Sjolander et al.
MATERIALS & DESIGN (2010)
A357 thixoforming feedstock produced by cooling slope casting
Yucel Birol
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)
Experimental study of structure formation in binary Al-Cu alloys at different cooling rates
D Eskin et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2005)
Influence of high-intensity ultrasound on grain refining performance of Al-5Ti-1B master alloy on aluminium
YF Han et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2005)
Effect of alloying elements on the segregation and dissolution of CuAl2 phase in Al-Si-Cu 319 alloys
Z Li et al.
JOURNAL OF MATERIALS SCIENCE (2003)
Strength-ductility behaviour of Al-Si-Cu-Mg casting alloys in T6 temper
CH Caceres et al.
INTERNATIONAL JOURNAL OF CAST METALS RESEARCH (2003)
Mass balance characterisation of Al-7Si-Mg alloy microstructures as a function of solution treatment time
PA Rometsch et al.
INTERNATIONAL JOURNAL OF CAST METALS RESEARCH (2001)
The effect of the cooling rate or the local solidification time and composition on the secondary dendrite arm spacing during solidification PART II: Al-Mg-Si alloys
V Ronto et al.
INTERNATIONAL JOURNAL OF CAST METALS RESEARCH (2001)
The effect of cooling rate and composition on the secondary dendrite arm spacing during solidification. Part I: Al-Cu-Si alloys
V Ronto et al.
INTERNATIONAL JOURNAL OF CAST METALS RESEARCH (2001)
Modelling of inoculation of metallic melts: Application to grain refinement of aluminium by Al-Ti-B
AL Greer et al.
ACTA MATERIALIA (2000)
Share Paper
