Related references
Note: Only part of the references are listed.Effect of inter layer idle time on thermal behavior for multi-layer single-pass thin-walled parts in GMAW-based additive manufacturing
Yangyang Lei et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
The effects of forced interpass cooling on the material properties of wire arc additively manufactured Ti6Al4V alloy
Bintao Wu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)
Additive manufacturing using WAAM with AA5183 wire
A. Horgar et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)
Oxide accumulation effects on wire plus arc layer-by-layer additive manufacture process
Xiangfang Xu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)
Wire arc additive manufacturing of Al-6Mg alloy using variable polarity cold metal transfer arc as power source
Chen Zhang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Additive manufacturing of metallic components - Process, structure and properties
T. DebRoy et al.
PROGRESS IN MATERIALS SCIENCE (2018)
Thermoelectric Cooling-Aided Bead Geometry Regulation in Wire and Arc-Based Additive Manufacturing of Thin-Walled Structures
Fang Li et al.
APPLIED SCIENCES-BASEL (2018)
The influence of build parameters and wire batch on porosity of wire and arc additive manufactured aluminium alloy 2319
E. M. Ryan et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)
Open-source wire and arc additive manufacturing system: formability, microstructures, and mechanical properties
X. Lu et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Thermal analysis for single-pass multi-layer GMAW based additive manufacturing using infrared thermography
Dongqing Yang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Fabrication of inclined thin-walled parts in multi-layer single-pass GMAW-based additive manufacturing with flat position deposition
Jun Xiong et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Effects of heat accumulation on the arc characteristics and metal transfer behavior in Wire Arc Additive Manufacturing of Ti6Al4V
Bintao Wu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Impact of Interlayer Dwell Time on Microstructure and Mechanical Properties of Nickel and Titanium Alloys
B. K. Foster et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2017)
Additive manufacturing of metals
Dirk Herzog et al.
ACTA MATERIALIA (2016)
The effect of inter-layer cold working and post-deposition heat treatment on porosity in additively manufactured aluminum alloys
Jianglong Gu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)
Structure-property relationships of common aluminum weld alloys utilized as feedstock for GMAW-based 3-D metal printing
Amberlee S. Haselhuhn et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
Effect of location on microstructure and mechanical properties of additive layer manufactured Inconel 625 using gas tungsten arc welding
J. F. Wang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
Wire plus Arc Additive Manufacturing
S. W. Williams et al.
MATERIALS SCIENCE AND TECHNOLOGY (2016)
Wire-feed additive manufacturing of metal components: technologies, developments and future interests
Donghong Ding et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Effect of inter-layer dwell time on distortion and residual stress in additive manufacturing of titanium and nickel alloys
Erik R. Denlinger et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)
Heat transfer and material flow during laser assisted multi-layer additive manufacturing
V. Manvatkar et al.
JOURNAL OF APPLIED PHYSICS (2014)
Adaptive control of deposited height in GMAW-based layer additive manufacturing
Jun Xiong et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2014)
Growth behavior of hydrogen micropores in aluminum alloys during high-temperature exposure
H. Toda et al.
ACTA MATERIALIA (2009)
Rapid prototyping of 4043 Al-alloy parts by VP-GTAW
HJ Wang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)