Related references
Note: Only part of the references are listed.Control of laminate quality for parts manufactured using the resin infusion process
S. M. R. Kazmi et al.
JOURNAL OF COMPOSITE MATERIALS (2019)
Effect of convection coefficient and thickness on optimal cure cycles for the manufacturing of wind turbine components using VARTM
G. Struzziero et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2019)
A Semi-Analytical Model to Predict Infusion Time and Reinforcement Thickness in VARTM and SCRIMP Processes
Felice Rubino et al.
POLYMERS (2019)
Simulation of vacuum assisted resin transfer molding process through dynamic system analysis
Fabiano T. Fracassi et al.
JOURNAL OF COMPOSITE MATERIALS (2018)
Cure kinetics and viscosity modeling for the optimization of cure cycles in a vacuum-bag-only prepreg process
Seong-Soon Hwang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Prediction of Defect Formation during Resin Impregnation Process through a Multi-Layered Fiber Preform in Resin Transfer Molding by a Proposed Analytical Model
Dong Gi Seong et al.
MATERIALS (2018)
Numerical modeling and experimental validation of nonisothermal resin infusion and cure processes in large composites
Liangkai Ma et al.
JOURNAL OF REINFORCED PLASTICS AND COMPOSITES (2017)
Simulating Resin Infusion through Textile Reinforcement Materials for the Manufacture of Complex Composite Structures
Robert S. Pierce et al.
ENGINEERING (2017)
Model-Assisted Control of Flow Front in Resin Transfer Molding Based on Real-Time Estimation of Permeability/Porosity Ratio
Bai-Jian Wei et al.
POLYMERS (2016)
Numerical study of the vacuum infusion process for laminated composites with different fiber orientations
Francisco J. Hurtado et al.
JOURNAL OF REINFORCED PLASTICS AND COMPOSITES (2015)
Analysis of the post-filling phase of the vacuum-assisted resin transfer molding process
Marc J. Robinson et al.
JOURNAL OF COMPOSITE MATERIALS (2014)
Modeling the resin flow and numerical simulation of the filling stage for vacuum-assisted resin infusion process
Bo Yang et al.
JOURNAL OF REINFORCED PLASTICS AND COMPOSITES (2014)
Out-of-autoclave cure cycle study of a resin film infusion process using in situ process monitoring
C. Garschke et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2012)
Experimental and numerical investigation of the VARTM process with a sandwich structure
Yu-Ti Jhan et al.
JOURNAL OF COMPOSITE MATERIALS (2012)
Optimization of the cycle time in resin transfer molding process by numerical simulation
Aouatif Saad et al.
JOURNAL OF REINFORCED PLASTICS AND COMPOSITES (2012)
Experimental study of dynamic air permeability for woven fabrics
Xueliang Xiao et al.
TEXTILE RESEARCH JOURNAL (2012)
Resin Flow Behavior Simulation of Grooved Foam Sandwich Composites with the Vacuum Assisted Resin Infusion (VARI) Molding Process
Chenhui Zhao et al.
MATERIALS (2012)
Effects of vacuum pressure, inlet pressure, and mold temperature on the void content, volume fraction of polyester/e-glass fiber composites manufactured with VARTM process
Vishwanath R. Kedari et al.
JOURNAL OF COMPOSITE MATERIALS (2011)
Development of Resin Infusion Process for Ultralight Large Composite Structures
Zaffar M. Khan et al.
ADVANCED MATERIALS FOR APPLIED SCIENCE AND TECHNOLOGY (2011)
Simulation of the reinforcement compaction and resin flow during the complete resin infusion process
Q. Govignon et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2010)
Effect of cure cycle on curing process and hardness for epoxy resin
J. Zhang et al.
EXPRESS POLYMER LETTERS (2009)
Development of a Helicopter Landing Gear Prototype using Resin Infusion Molding
Wen-Bin Young
JOURNAL OF REINFORCED PLASTICS AND COMPOSITES (2009)
Full field monitoring of the resin flow and laminate properties during the resin infusion process
Q. Govignon et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2008)
Numerical modelling of liquid infusion into fibrous media undergoing compaction
Pierre Celle et al.
EUROPEAN JOURNAL OF MECHANICS A-SOLIDS (2008)
Injection gate definition for improving the accuracy of liquid composite molding process simulation
Chensong Dong
JOURNAL OF COMPOSITE MATERIALS (2007)
Investigation of pressure profile and flow progression in vacuum infusion process
D. Modi et al.
PLASTICS RUBBER AND COMPOSITES (2007)
Phase-field simulations of interfacial dynamics in viscoelastic fluids using finite elements with adaptive meshing
Pengtao Yue et al.
JOURNAL OF COMPUTATIONAL PHYSICS (2006)
An equivalent medium method for the vacuum assisted resin transfer molding process simulation
Chensong (Jonathan) Dong
JOURNAL OF COMPOSITE MATERIALS (2006)
Use of resin transfer molding simulation to predict flow, saturation, and compaction in the VARTM process
NC Correia et al.
JOURNAL OF FLUIDS ENGINEERING-TRANSACTIONS OF THE ASME (2004)
Simultaneous gate and vent location optimization in liquid composite molding processes
A Gokce et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2004)
A study of cure kinetics by the use of dynamic differential scanning calorimetry
MK Um et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2002)
Share Paper
