Related references
Note: Only part of the references are listed.Cooling Ability/Capacity and Exergy Penalty Analysis of Each Heat Sink of Modern Supersonic Aircraft
Yu-Feng Mao et al.
ENTROPY (2019)
A gas-atomized spray cooling system integrated with an ejector loop: Ejector modeling and thermal performance analysis
Ji-Xiang Wang et al.
ENERGY CONVERSION AND MANAGEMENT (2019)
Evaluation and development of temperature-based empirical models for estimating daily global solar radiation in humid regions
Junliang Fan et al.
ENERGY (2018)
A novel steam ejector with pressure regulation to optimize the entrained flow passage for performance improvement in MED-TVC desalination system
Yongzhi Tang et al.
ENERGY (2018)
Supersonic liquefaction properties of natural gas in the Laval nozzle
Jiang Bian et al.
ENERGY (2018)
Investigation of heat transfer mechanism of low environmental pressure large-space spray cooling for near-space flight systems
Ji-Xiang Wang et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2018)
A hybrid cooling system combining self-adaptive single-phase mechanically pumped fluid loop and gravity-immune two-phase spray module
Ji-Xiang Wang et al.
ENERGY CONVERSION AND MANAGEMENT (2018)
SOFC-APU systems for aircraft: A review
M. D. Fernandes et al.
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2018)
Investigation of a gravity-immune chip-level spray cooling for thermal protection of laser-based wireless power transmission system
Ji-Xiang Wang et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2017)
A critical review of traditional and emerging techniques and fluids for electronics cooling
S. M. Sohel Murshed et al.
RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2017)
Numerical study of high-overload effect on liquid film of spray cooling
Pang Liping et al.
APPLIED THERMAL ENGINEERING (2017)
Experimental investigation on the performance of a water spray cooling system
Zhou Nianyong et al.
APPLIED THERMAL ENGINEERING (2017)
Structure improvements and numerical simulation of supersonic separators
Jiang Bian et al.
CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION (2016)
Influence of chamber pressure on heat transfer characteristics of a closed loop R134-a spray cooling
Jionghui Liu et al.
EXPERIMENTAL THERMAL AND FLUID SCIENCE (2016)
Spray cooling and flash evaporation cooling: The current development and application
Wen-Long Cheng et al.
RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2016)
Investigation of a spray cooling system with two nozzles for space application
Ji-Xiang Wang et al.
APPLIED THERMAL ENGINEERING (2015)
Heat transfer enhancement of spray cooling with ammonia by microcavity surfaces
B. H. Yang et al.
APPLIED THERMAL ENGINEERING (2013)
Experimental studies on air-assisted impinging jet atomization
Madan Mohan Avulapati et al.
INTERNATIONAL JOURNAL OF MULTIPHASE FLOW (2013)
Experimental characterization of heat transfer in non-boiling spray cooling with two nozzles
Yujia Tao et al.
APPLIED THERMAL ENGINEERING (2011)
Cooling Performance of a 16-Nozzle Array in Variable Gravity
Levi J. Elston et al.
JOURNAL OF THERMOPHYSICS AND HEAT TRANSFER (2009)
Spray cooling heat transfer: Technology overview and assessment of future challenges for micro-gravity application
Eric A. Silk et al.
ENERGY CONVERSION AND MANAGEMENT (2008)
Active performance enhancement of spray cooling
Anna A. Pavlova et al.
INTERNATIONAL JOURNAL OF HEAT AND FLUID FLOW (2008)
Effects of high subcooling on two-phase spray cooling and critical heat flux
Milan Visaria et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2008)
Spray cooling of enhanced surfaces: Impact of structured surface geometry and spray axis inclination
Eric A. Silk et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2006)
Evaporative heat transfer characteristics of a water spray on micro-structured silicon surfaces
CC Hsieh et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2006)
Spray cooling characteristics of water and R-134a. Part II: transient cooling
SS Hsieh et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2004)
Spray cooling thermal management for increased device reliability
T Cader et al.
IEEE TRANSACTIONS ON DEVICE AND MATERIALS RELIABILITY (2004)
Heat transfer characteristics of spray cooling in a closed loop
LC Lin et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2003)
Spray cooling under reduced gravity condition
K Yoshida et al.
JOURNAL OF HEAT TRANSFER-TRANSACTIONS OF THE ASME (2001)
Share Paper
