Related references
Note: Only part of the references are listed.Strong and ductile medium Mn steel without transformation-induced plasticity effect
B. B. He et al.
MATERIALS RESEARCH LETTERS (2018)
Obtaining high strength and high plasticity in a Mg-3A1-1Zn plate using pre -tension and annealing treatments
Feilong Guo et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2017)
Evolution of microstructure and texture in copper during repetitive extrusion-upsetting and subsequent annealing
Q. Chen et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2017)
Mechanical properties and deformation mechanism of Mg-Al-Zn alloy with gradient microstructure in grain size and orientation
Liu Chen et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Towards strength-ductility synergy through the design of heterogeneous nanostructures in metals
Evan Ma et al.
MATERIALS TODAY (2017)
Fabricating interstitial-free steel with simultaneous high strength and good ductility with homogeneous layer and lamella structure
Ling Zhang et al.
SCRIPTA MATERIALIA (2017)
Heterogeneous materials: a new class of materials with unprecedented mechanical properties
Xiaolei Wu et al.
MATERIALS RESEARCH LETTERS (2017)
Improving mechanical properties of extruded Mg-Al alloy with a bimodal grain structure through alloying addition
Sung Hyuk Park et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2015)
Improved mechanical properties of AZ31 magnesium alloy sheets by repeated cold rolling and annealing using a small pass reduction
Hua Zhang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)
Heterogeneous lamella structure unites ultrafine-grain strength with coarse-grain ductility
Xiaolei Wu et al.
PROCEEDINGS OF THE NATIONAL ACADEMY OF SCIENCES OF THE UNITED STATES OF AMERICA (2015)
Achieving high strength and high ductility in magnesium alloy using hard-plate rolling (HPR) process
Hui-Yuan Wang et al.
SCIENTIFIC REPORTS (2015)
Harmonic-structured copper: performance and proof of fabrication concept based on severe plastic deformation of powders
Choncharoen Sawangrat et al.
JOURNAL OF MATERIALS SCIENCE (2014)
Influence of rolling speed on microstructure and mechanical properties of AZ31 Mg alloy rolled by large strain hot rolling
Fei Guo et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Extraordinary strain hardening by gradient structure
XiaoLei Wu et al.
PROCEEDINGS OF THE NATIONAL ACADEMY OF SCIENCES OF THE UNITED STATES OF AMERICA (2014)
Making strong nanomaterials ductile with gradients
K. Lu
SCIENCE (2014)
Modeling inelastic behavior of magnesium alloys during cyclic loading-unloading
H. Wang et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2013)
Fabrication of Mg-Al-Zn-Mn alloy sheets with homogeneous fine-grained structures using high strain-rate rolling in a wide temperature range
S. Q. Zhu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
Effect of grain size on prismatic slip in Mg-3Al-1Zn alloy
S. M. Razavi et al.
SCRIPTA MATERIALIA (2012)
Development of ultrahigh strength and high ductility in nanostructured iron alloys with lattice softening and nanotwins
Kaveh Edalati et al.
SCRIPTA MATERIALIA (2012)
An investigation into the mechanical behavior and microstructural evolution of the accumulative roll bonded AZ31 Mg alloy upon annealing
Ali A. Roostaei et al.
MATERIALS & DESIGN (2011)
Effect of grain size distribution and texture on the cold extrusion behavior and mechanical properties of AZ31 Mg alloy
H. Y. Chao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
Revealing Extraordinary Intrinsic Tensile Plasticity in Gradient Nano-Grained Copper
T. H. Fang et al.
SCIENCE (2011)
Effects of hot rolling processing on microstructures and mechanical properties of Mg-3%Al-1%Zn alloy sheet
L. Jin et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
Improvement of formability of Mg-Al-Zn alloy sheet at low temperatures using differential speed rolling
Xinsheng Huang et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2009)
Microstructure and mechanical properties in an AZ31 magnesium alloy sheet fabricated by asymmetric hot extrusion
L. L. Chang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Grain size effects on the tensile properties and deformation mechanisms of a magnesium alloy, AZ31B, sheet
A. Jain et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Dynamic recrystallization in AZ31 magnesium alloy
S. M. Fatemi-Varzaneh et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2007)
Deformation behavior of ultrafine-grain (UFG) AZ31B Mg alloy at room temperature
Q. Yang et al.
ACTA MATERIALIA (2006)
Optimization of strength and ductility in nanocrystalline and ultrafine grained metals
CC Koch
SCRIPTA MATERIALIA (2003)
Al-Mg alloy engineered with bimodal grain size for high strength and increased ductility
D Witkin et al.
SCRIPTA MATERIALIA (2003)
The activity of non-basal slip systems and dynamic recovery at room temperature in fine-grained AZ31B magnesium alloys
J Koike et al.
ACTA MATERIALIA (2003)
High tensile ductility in a nanostructured metal
YM Wang et al.
NATURE (2002)
Paradox of strength and ductility in metals processed by severe plastic deformation
RZ Valiev et al.
JOURNAL OF MATERIALS RESEARCH (2002)
Mechanical behavior and microstructure of a thermally stable bulk nanostructured Al alloy
VL Tellkamp et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2001)
Share Paper
