Related references
Note: Only part of the references are listed.Voids in fiber-reinforced polymer composites: A review on their formation, characteristics, and effects on mechanical performance
Mahoor Mehdikhani et al.
JOURNAL OF COMPOSITE MATERIALS (2019)
Insights from in-situ X-ray computed tomography during axial impregnation of unidirectional fiber beds
Natalie M. Larson et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2018)
X-ray computed tomography of polymer composites
S. C. Garcea et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2018)
3D in situ observations of the compressibility and pore transport in Sheet Moulding Compounds during the early stages of compression moulding
D. Ferre Sentis et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2017)
Characterization and modeling of the polymerization-dependent moisture absorption behavior of an epoxy-carbon fiber-reinforced composite material
Basile de Parscau du Plessix et al.
JOURNAL OF COMPOSITE MATERIALS (2016)
Improved simplified approach for the prediction of porosity growth during the curing of composites parts
B. de Parscau du Plessix et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2016)
High-resolution computed tomography in resin infused woven carbon fibre composites with voids
S. M. Sisodia et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2016)
An in situ investigation of microscopic infusion and void transport during vacuum-assisted infiltration by means of X-ray computed tomography
Joaquim Vila et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2015)
Cure behaviour and void development within rapidly cured out-of-autoclave composites
S. L. Agius et al.
COMPOSITES PART B-ENGINEERING (2013)
Optimization of curing cycle in carbon fiber-reinforced laminates: Void distribution and mechanical properties
S. Hernandez et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2013)
3D damage characterisation and the role of voids in the fatigue of wind turbine blade materials
J. Lambert et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2012)
Characterisation of voids in fibre reinforced composite materials
John Eric Little et al.
NDT & E INTERNATIONAL (2012)
Effect of curing cycle on void distribution and interlaminar shear strength in polymer-matrix composites
S. Hernandez et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2011)
Towards the 3D in situ characterisation of deformation micro-mechanisms within a compressed bundle of fibres
P. Latil et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2011)
Measuring the impregnation of an out-of-autoclave prepreg by micro-CT
T. Centea et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2011)
Void formation in composite prepregs - Effect of dissolved moisture
L. K. Grunenfelder et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2010)
In situ and real-time 3-D microtomography investigation of dendritic solidification in an Al-10 wt.% Cu alloy
N. Limodin et al.
ACTA MATERIALIA (2009)
X-ray phase contrast microtomography for the analysis of the fibrous microstructure of SMC composites
T. -H. Le et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2008)
The effect of voids on the flexural fatigue performance of unidirectional carbon fibre composites developed for wind turbine applications
A. R. Chambers et al.
INTERNATIONAL JOURNAL OF FATIGUE (2006)
Effects of cure cycles on void content and mechanical properties of composite laminates
L Liu et al.
COMPOSITE STRUCTURES (2006)
Effects of void geometry on elastic properties of unidirectional fiber reinforced composites
H Huang et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2005)
Simultaneous phase and amplitude extraction from a single defocused image of a homogeneous object
D Paganin et al.
JOURNAL OF MICROSCOPY (2002)
The influence of porosity on the interlaminar shear strength of carbon/epoxy and carbon/bismaleimide fabric laminates
ML Costa et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2001)
Share Paper
