Related references
Note: Only part of the references are listed.Analysis of the effects of wall temperature swing on reciprocating internal combustion engine processes
Peter Andruskiewicz et al.
INTERNATIONAL JOURNAL OF ENGINE RESEARCH (2018)
Inverse Analysis of In-Cylinder Gas-Wall Boundary Conditions: Investigation of a Yttria-Stabilized Zirconia Thermal Barrier Coating for Homogeneous Charge Compression Ignition
Ryan O'Donnell et al.
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME (2017)
Impact of a Yttria-Stabilized Zirconia Thermal Barrier Coating on HCCI Engine Combustion, Emissions, and Efficiency
Tommy Powell et al.
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME (2017)
Estimation of Thermal Barrier Coating Surface Temperature and Heat Flux Profiles in a Low Temperature Combustion Engine Using a Modified Sequential Function Specification Approach
Ryan N. O'Donnell et al.
JOURNAL OF HEAT TRANSFER-TRANSACTIONS OF THE ASME (2017)
EXPERIMENTAL INVESTIGATION ON FUEL FILM FORMATION BY SPRAY IMPINGEMENT ON FLAT WALLS WITH DIFFERENT SURFACE ROUGHNESS
Hongliang Luo et al.
ATOMIZATION AND SPRAYS (2017)
Reduction of Heat Loss and Improvement of Thermal Efficiency by Application of Temperature Swing Insulation to Direct-Injection Diesel Engines
Yoshifumi Wakisaka et al.
SAE INTERNATIONAL JOURNAL OF ENGINES (2016)
The Solution Precursor Plasma Spray (SPPS) Process: A Review with Energy Considerations
Eric H. Jordan et al.
JOURNAL OF THERMAL SPRAY TECHNOLOGY (2015)
The impact of a magnesium zirconate thermal barrier coating on homogeneous charge compression ignition operational variability and the formation of combustion chamber deposits
Mark A. Hoffman et al.
INTERNATIONAL JOURNAL OF ENGINE RESEARCH (2015)
Low Thermal Conductivity Yttria-Stabilized Zirconia Thermal Barrier Coatings Using the Solution Precursor Plasma Spray Process
Eric H. Jordan et al.
JOURNAL OF THERMAL SPRAY TECHNOLOGY (2014)
Concept of Temperature Swing Heat Insulation in Combustion Chamber Walls, and Appropriate Thermo-Physical Properties for Heat Insulation Coat
Hidemasa Kosaka et al.
SAE INTERNATIONAL JOURNAL OF ENGINES (2013)
Assessment of Residual Mass Estimation Methods for Cylinder Pressure Heat Release Analysis of HCCI Engines With Negative Valve Overlap
Elliott A. Ortiz-Soto et al.
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME (2012)
Investigating the Development of Thermal Stratification from the Near-Wall Regions to the Bulk-Gas in an HCCI Engine with Planar Imaging Thermometry
Nicolas Dronniou et al.
SAE INTERNATIONAL JOURNAL OF ENGINES (2012)
PLIF Measurements of Thermal Stratification in an HCCI Engine under Fired Operation
Jordan Snyder et al.
SAE INTERNATIONAL JOURNAL OF ENGINES (2011)
Hybrid Electric Vehicle Powertrain and Control Strategy Optimization to Maximize the Synergy with a Gasoline HCCI Engine
Benjamin Lawler et al.
SAE INTERNATIONAL JOURNAL OF ENGINES (2011)
Thermal barrier coatings made by the solution precursor plasma spray process
Maurice Gell et al.
JOURNAL OF THERMAL SPRAY TECHNOLOGY (2008)
Low-thermal-conductivity plasma-sprayed thermal barrier coatings with engineered microstructures
Amol D. Jadhav et al.
ACTA MATERIALIA (2006)
Deposition mechanisms of thermal barrier coatings in the solution precursor plasma spray process
LD Xie et al.
SURFACE & COATINGS TECHNOLOGY (2004)
Highly durable thermal barrier coatings made by the solution precursor plasma spray process
M Gell et al.
SURFACE & COATINGS TECHNOLOGY (2004)
Share Paper
