Related references
Note: Only part of the references are listed.Homogeneity analysis of square meter-sized electrodes for PEM electrolysis and PEM fuel cells
Andrea Burdzik et al.
JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH (2018)
Binder migration during drying of lithium-ion battery electrodes: Modelling and comparison to experiment
F. Font et al.
JOURNAL OF POWER SOURCES (2018)
Catalyst Layer Ink Interactions That Affect Coatability
Marm B. Dixit et al.
JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2018)
Turbulent superstructures in Rayleigh-Benard convection
Ambrish Pandey et al.
NATURE COMMUNICATIONS (2018)
A new setup for the quantitative analysis of drying by the use of gas-phase FTIR-spectroscopy
F. Scheepers et al.
REVIEW OF SCIENTIFIC INSTRUMENTS (2018)
Layer Formation from Polymer Carbon-Black Dispersions
Fabian Scheepers et al.
COATINGS (2018)
Enhanced PEDOT adhesion on solid substrates with electrografted P(EDOT-NH2)
Liangqi Ouyang et al.
SCIENCE ADVANCES (2017)
The roles of wettability and surface tension in droplet formation during inkjet printing
Bing He et al.
SCIENTIFIC REPORTS (2017)
Reverse gravure coating for roll-to-roll production of organic photovoltaics
Doojin Vak et al.
SOLAR ENERGY MATERIALS AND SOLAR CELLS (2016)
An overview of cracks and interfacial voids in membrane electrode assemblies in polymer electrolyte fuel cells
Shohji Tsushima et al.
JOURNAL OF THERMAL SCIENCE AND TECHNOLOGY (2015)
Drying Kinetics and Microstructural and SensoryProperties of Black Chokeberry (Aronia melanocarpa) as Affected by Drying Method
Angel Calin-Sanchez et al.
FOOD AND BIOPROCESS TECHNOLOGY (2015)
Stress Development in Hard Particle Coatings in the Absence of Lateral Drying
Kyle K. Price et al.
JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2015)
All-Printed Flexible Organic Transistors Enabled by Surface Tension-Guided Blade Coating
Adrien Pierre et al.
ADVANCED MATERIALS (2014)
Aggregation and morphology control enables multiple cases of high-efficiency polymer solar cells
Yuhang Liu et al.
NATURE COMMUNICATIONS (2014)
Statistical investigations of basis weight and thickness distribution of continuously produced fuel cell electrodes
M. Staehler et al.
JOURNAL OF POWER SOURCES (2013)
Spray-Assisted Polyelectrolyte Multilayer Buildup: from Step-by-Step to Single-Step Polyelectrolyte Film Constructions
Pierre Schaaf et al.
ADVANCED MATERIALS (2012)
Ambient fabrication of flexible and large-area organic light-emitting devices using slot-die coating
Andreas Sandstrom et al.
NATURE COMMUNICATIONS (2012)
Strategies for the Fabrication of Porous Platinum Electrodes
Arne Kloke et al.
ADVANCED MATERIALS (2011)
Structure-Morphology-Property Relationships of Non-Perfluorinated Proton-Conducting Membranes
Timothy J. Peckham et al.
ADVANCED MATERIALS (2010)
Experiment evidence on the temperature dependence of desiccation cracking behavior of clayey soils
Chao-Sheng Tang et al.
ENGINEERING GEOLOGY (2010)
Recent Progress in Polymer Solar Cells: Manipulation of Polymer: Fullerene Morphology and the Formation of Efficient Inverted Polymer Solar Cells
Li-Min Chen et al.
ADVANCED MATERIALS (2009)
Drying-Induced Cracks in Thin Film Fabricated from Colloidal Dispersions
Peng Xu et al.
DRYING TECHNOLOGY (2009)
Drying of thin film polymer solar cells
B. Schmidt-Hansberg et al.
EUROPEAN PHYSICAL JOURNAL-SPECIAL TOPICS (2009)
Dependence of polymer electrolyte fuel cell performance on preparation conditions of slurry for catalyst layers
Yoshiyuki Komoda et al.
JOURNAL OF POWER SOURCES (2009)
Stress Development During Drying of Aqueous Zirconia Based Tape Casting Slurries Measured by Transparent Substrate Deflection Method
Christiane Bauer et al.
JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2009)
Cracking in drying colloidal films
Karnail B. Singh et al.
PHYSICAL REVIEW LETTERS (2007)
Solution-processed silicon films and transistors
T Shimoda et al.
NATURE (2006)
Cracking in drying latex films
MS Tirumkudulu et al.
LANGMUIR (2005)
Manufacture of Robust Catalyst Layers for the DMFC
M. Schonert et al.
FUEL CELLS (2004)
Shape evolution and stress development during latex-silica film formation
CJ Martinez et al.
LANGMUIR (2002)
Influence of humidity on the cracking patterns formed during the drying of sol-gel drops
BD Caddock et al.
JOURNAL OF MATERIALS SCIENCE (2002)
Share Paper
