Related references
Note: Only part of the references are listed.Analysis and Fem Simulation Methodology of Dynamic Behavior of Human Rotator Cuff in Repetitive Routines: Musician Case Study
Manuel Islan et al.
JOURNAL OF MEDICAL SYSTEMS (2018)
Design of an Orthopedic Product by Using Additive Manufacturing Technology: The Arm Splint
Fernando Blaya et al.
JOURNAL OF MEDICAL SYSTEMS (2018)
Filament Advance Detection Sensor for Fused Deposition Modelling 3D Printers
Enrique Soriano Heras et al.
SENSORS (2018)
Finite Element Simulations of Hard-On-Soft Hip Joint Prosthesis Accounting for Dynamic Loads Calculated from a Musculoskeletal Model during Walking
Alessandro Ruggiero et al.
MATERIALS (2018)
Finite Element Simulation and Analysis of the behavior under load of a human shoulder
Manuel Islan Marcos et al.
SIXTH INTERNATIONAL CONFERENCE ON TECHNOLOGICAL ECOSYSTEMS FOR ENHANCING MULTICULTURALITY (TEEM'18) (2018)
Design and prototyping by additive manufacturing of a functional splint for rehabilitation of Achilles tendon intrasubstance rupture
Fernando Blaya Haro et al.
SIXTH INTERNATIONAL CONFERENCE ON TECHNOLOGICAL ECOSYSTEMS FOR ENHANCING MULTICULTURALITY (TEEM'18) (2018)
Airborne particle emission of a commercial 3D printer: the effect of filament material and printing temperature
L. Stabile et al.
INDOOR AIR (2017)
On the biotribology of total knee replacement: a new roughness measurements protocol on in vivo condyles considering the dynamic loading from musculoskeletal multibody model
Alessandro Ruggiero et al.
MEASUREMENT (2017)
Optimisation of machining parameters during ball end milling of hardened steel with various surface inclinations
S. Wojciechowski et al.
MEASUREMENT (2017)
Investigation of the adhesion properties of direct 3D printing of polymers and nanocomposites on textiles: Effect of FDM printing process parameters
Razieh Hashemi Sanatgar et al.
APPLIED SURFACE SCIENCE (2017)
On the tribological behavior of retrieved hip femoral heads affected by metallic debris. A comparative investigation by stylus and optical profilometer for a new roughness measurement protocol
Massimiliano Merola et al.
MEASUREMENT (2016)
Experimental comparison on tribological pairs UHMWPE/TIAL6V4 alloy, UHMWPE/AISI316L austenitic stainless and UHMWPE/AL2O3 ceramic, under dry and lubricated conditions
Alessandro Ruggiero et al.
TRIBOLOGY INTERNATIONAL (2016)
Experimental analysis of an extrusion system for additive manufacturing based on polymer pellets
N. Volpato et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
A review of melt extrusion additive manufacturing processes: II. Materials, dimensional accuracy, and surface roughness
Brian N. Turner et al.
RAPID PROTOTYPING JOURNAL (2015)
Experimental analysis of tribological behavior of UHMWPE against AISI420C and against TiAl6V4 alloy under dry and lubricated conditions
Alessandro Ruggiero et al.
TRIBOLOGY INTERNATIONAL (2015)
BeamMaker: an open hardware high-resolution digital fabricator for the masses
Ariel Calderon et al.
RAPID PROTOTYPING JOURNAL (2014)
Approximate closed-form solution of the synovial fluid film force in the human ankle joint with non-Newtonian lubricant
Ruggiero Alessandro et al.
TRIBOLOGY INTERNATIONAL (2013)
Approximate Analytical Model for the Squeeze-Film Lubrication of the Human Ankle Joint with Synovial Fluid Filtrated by Articular Cartilage
Alessandro Ruggiero et al.
TRIBOLOGY LETTERS (2011)
Personal Fabrication
Graeme Stemp-Morlock
COMMUNICATIONS OF THE ACM (2010)
Osteoconduction and osteoinduction of low-temperature 3D printed bioceramic implants
Pamela Habibovic et al.
BIOMATERIALS (2008)
A new method for printer calibration and contour accuracy manufacturing with 3D-print technology
Sebastian Stopp et al.
RAPID PROTOTYPING JOURNAL (2008)
Share Paper
