Related references
Note: Only part of the references are listed.Influence of edge hone radius on cutting forces, surface integrity, and surface oxidation in hard milling of AISI H13 steel
Binxun Li et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Wear mechanisms of uncoated and coated carbide tools when machining Ti6Al4V using LN2 and cooled N2
S. Sartori et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Predictive cutting force model for a cryogenic machining process incorporating the phase transformation of Ti-6Al-4V
Do Young Kim et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Experimental study on chip deformation of Ti-6Al-4V titanium alloy in cryogenic cutting
Wei Zhao et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Effect of cutting parameters on surface quality in multi-step turning of Ti-6Al-4V titanium alloy
Guanming Hou et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Effects of cryogenic cooling on the surface integrity in hard turning of AISI D6 steel
Welber Vasconcelos Leadebal et al.
JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2018)
Tool wear and cutting forces under cryogenic machining of titanium alloy (Ti17)
Sabrine Trabelsi et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Effects of internal cooling by cryogenic on the machinability of hardened steel
A. K. M. Khabirul Islam et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Thermal analysis during turning of AZ31 magnesium alloy under dry and cryogenic conditions
Mohd Danish et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Impact of supply conditions of liquid nitrogen on tool wear and surface integrity when machining the Ti-6Al-4V titanium alloy
Y. Ayed et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Study of surface roughness and cutting forces using ANN, RSM, and ANOVA in turning of Ti-6Al-4V under cryogenic jets applied at flank and rake faces of coated WC tool
Mozammel Mia et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Effect of cutting edge radius on surface roughness and tool wear in hard turning of AISI 52100 steel
T. Zhao et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
The surface integrity of AISI 1010 and AISI 4340 steels subjected to face milling
Jean Carlos C. Pereira et al.
JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2017)
Tool wear and surface integrity of inconel 718 in dry and cryogenic coolant at high cutting speed
A. H. Musfirah et al.
WEAR (2017)
Tool life and surface integrity when turning titanium aluminides with PCD tools under conventional wet cutting and cryogenic cooling
Paolo C. Priarone et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
Cryogenic cooling-induced process performance and surface integrity in drilling CFRP composite material
T. Xia et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
Material Model Application Considering Strain Softening for Cutting Simulation of 11-6Al-4V Alloy and Its Experimental Validation
Hyun-Jin Choi et al.
INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING (2016)
Tool life improvement in cryogenic cooled milling of the preheated Ti-6Al-4V
Ineon Lee et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
A comparative study on cutting performance of rake-flank face structured cutting tool in orthogonal cutting of AISI/SAE 4140
Anis Fatima et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
A study on the influence of cutting parameters on forces during machining the multiphase V-microalloyed steel
V. Sivaraman et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Experimental investigation of surface integrity in finish dry hard turning of hardened tool steel at different hardness levels
Linhu Tang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Evaluation of machining performance in cryogenic machining of Inconel 718 and comparison with dry and MQL machining
Yusuf Kaynak
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2014)
Effects of cutting conditions on microhardness and microstructure in high-speed milling of H13 tool steel
Fuzeng Wang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2014)
Microhardness and Surface Integrity in Turning Process of Duplex Stainless Steel (DSS) for Different Cutting Conditions
G. Krolczyk et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2014)
Cryogenic Machining-Induced Surface Integrity: A Review and Comparison with Dry, MQL, and Flood-Cooled Machining
Yusuf Kaynak et al.
MACHINING SCIENCE AND TECHNOLOGY (2014)
EXPERIMENTAL STUDY ON CUTTING FORCES AND SURFACE INTEGRITY IN HIGH-SPEED SIDE MILLING OF Ti-6Al-4V TITANIUM ALLOY
Fuzeng Wang et al.
MACHINING SCIENCE AND TECHNOLOGY (2014)
Surface Integrity and Fatigue Behavior for High-Speed Milling Ti-10V-2Fe-3AI Titanium Alloy
C. F. Yao et al.
JOURNAL OF FAILURE ANALYSIS AND PREVENTION (2014)
Analysis of the white layers formed during machining of hardened AISI 52100 steel under dry and cryogenic cooling conditions
Domenico Umbrello
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)
The effects of cryogenic cooling on surface integrity in hard machining: A comparison with dry machining
Domenico Umbrello et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2012)
Process design space for optimal surface integrity in finish hard milling of tool steel
S. Zhang et al.
PRODUCTION ENGINEERING-RESEARCH AND DEVELOPMENT (2012)
Cryogenic turning of the Ti-6Al-4V alloy with modified cutting tool inserts
M. Dhananchezian et al.
CRYOGENICS (2011)
Influence of material microstructure changes on surface integrity in hard machining of AISI 52100 steel
Domenico Umbrello
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2011)
New observations on tool life, cutting forces and chip morphology in cryogenic machining Ti-6Al-4V
M. J. Bermingham et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2011)
Surface integrity in cryogenic machining of nickel based alloy-Inconel 718
F. Pusavec et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2011)
A comprehensive experimental study on surface integrity by end milling Ti-6Al-4V
J. Sun et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
Analysis of residual stresses induced by dry turning of difficult-to-machine materials
J. C. Outeiro et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2008)
The influence of cutter orientation and workpiece angle on machinability when high-speed milling Inconel 718 under finishing conditions
D. K. Aspinwall et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2007)
Share Paper
