Related references
Note: Only part of the references are listed.Investigations of tangential ultrasonic vibration turning of Ti6Al4V using finite element method
Jiajia Zhang et al.
INTERNATIONAL JOURNAL OF MATERIAL FORMING (2019)
Rotary ultrasonic drilling of needle-punched carbon/carbon composites: comparisons with conventional twist drilling and high-speed drilling
Chenwei Shan et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Numerical investigation of the performance of elliptical vibration cutting in machining of AISI 1045 steel
Chao Kong et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Analytical modeling of tool-workpiece contact rate and experimental study in ultrasonic vibration-assisted milling of Ti-6Al-4V
Chenbing Ni et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2018)
Evaluation of novel tool geometries in dry drilling aluminium 2024-T351/titanium Ti6Al4V stack
Zhaoju Zhu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)
Study on rotary ultrasonic-assisted drilling of titanium alloys (Ti6Al4V) using 8-facet drill under no cooling condition
Zhe Li et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Ultrasonic assistance in drilling: FEM analysis and experimental approaches
Hossein Paktinat et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Drilling in carbon/epoxy composites: Experimental investigations and finite element implementation
Vaibhav A. Phadnis et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2013)
Neural network approach for estimating the residual tensile strength after drilling in uni-directional glass fiber reinforced plastic laminates
Roshan Mishra et al.
MATERIALS & DESIGN (2010)
Analysis of ultrasonic-assisted drilling of Ti6Al4V
J. Pujana et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2009)
Wear mechanisms and tool life management of WC-Co drills during dry high speed drilling of woven carbon fibre composites
Sanjay Rawat et al.
WEAR (2009)
Analysis of parametric influence on delamination in high-speed drilling of carbon fiber reinforced plastic composites
V. N. Gaitonde et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Delamination analysis in high speed drilling of carbon fiber reinforced plastics (CFRP) using artificial neural network model
S. R. Karnik et al.
MATERIALS & DESIGN (2008)
The effect of cutting tool geometry on thrust force and delamination when drilling glass fibre reinforced plastic composite
A. M. Abrao et al.
MATERIALS & DESIGN (2008)
Drilling of uni-directional glass fiber reinforced plastics: Experimental and finite element study
I. Singh et al.
MATERIALS & DESIGN (2008)
Vibration excitation and energy transfer during ultrasonically assisted drilling
V. I. Babitsky et al.
JOURNAL OF SOUND AND VIBRATION (2007)
Spiral point drill temperature and stress in high-throughput drilling of titanium
Rui Li et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2007)
Feasibility study of the ultrasonic vibration assisted drilling of Inconel superalloy
Y. S. Liao et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2007)
A three-dimensional inverse problem in estimating the applied heat flux of a titanium drilling - Theoretical and experimental studies
Cheng-Hung Huang et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2007)
Temperature measurement of cutting edge in drilling - Effect of oil mist
T. Ueda et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2007)
Investigation on thrust in vibration drilling of fiber-reinforced plastics
X Wang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
A model for predicting the heat flow into the workpiece in dry drilling
M Bono et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2002)
Influence of thermal effects on hole quality in dry drilling, part 1: A thermal model of workpiece temperatures
S Kalidas et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2002)
Share Paper
