Related references
Note: Only part of the references are listed.Creep properties, creep deformation behavior, and microstructural evolution of 9Cr-3W-3Co-1CuVNbB martensite ferritic steel
Bo Xiao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Experimental evidence of liquid feeding during solidification of a steel
G. Agarwal et al.
SCRIPTA MATERIALIA (2018)
Effects of cooling rates on δ-ferrite/γ-austenite formation and martensitic transformation in modified ferritic heat resistant steel
Xiaosheng Zhou et al.
FUSION ENGINEERING AND DESIGN (2017)
Hot tearing susceptibility of Fe-20. 96Cr-2. 13Ni-0. 15N-4. 76Mn-0. OlMo duplex stainless steel
Zhi-qiang Wei et al.
JOURNAL OF IRON AND STEEL RESEARCH INTERNATIONAL (2017)
Hot tear characterization of AlCu5MgTi and AlSi9 casting alloys using an instrumented constrained six rods casting method
Abderrazzak Hamadellah et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Experimental and Theoretical Studies of the Hot Tearing Behavior of Al-xZn-2Mg-2Cu Alloys
Y. Li et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2017)
A review on hot tearing of magnesium alloys
Jiangfeng Song et al.
JOURNAL OF MAGNESIUM AND ALLOYS (2016)
Determination of interfacial heat transfer coefficients in a sand mould casting process using an optimised inverse analysis
Gianfranco Palumbo et al.
APPLIED THERMAL ENGINEERING (2015)
Thermal and deformation-induced phase transformation behavior of Fe-15Cr-3Mn-3Ni-0.1N-(0.05-0.25)C austenitic and austenitic-martensitic cast stainless steels
M. Wendler et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)
Effect of Zn addition on hot tearing behaviour of Mg-0.5Ca-xZn alloys
Jiangfeng Song et al.
MATERIALS & DESIGN (2015)
h Research and Development of Heat-Resistant Materials for Advanced USC Power Plants with Steam Temperatures of 700 °C and Above
Fujio Abe
ENGINEERING (2015)
Development of an inverse heat conduction model and its application to determination of heat transfer coefficient during casting solidification
Liqiang Zhang et al.
HEAT AND MASS TRANSFER (2014)
Heat transfer behavior of top side-pouring twin-roll casting
De Wang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2014)
Role of Grain Refinement in the Hot Tearing of Cast Al-Cu Alloy
Shimin Li et al.
METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE (2013)
Influence of mould design on the solidification of heavy forging ingots of low alloy steels by numerical simulation
A. Kermanpur et al.
MATERIALS & DESIGN (2010)
Study of hot tearing of A206 aluminum alloy using Instrumented Constrained T-shaped Casting method
M. R. Nasr Esfahani et al.
MATERIALS CHARACTERIZATION (2010)
Influence of yttrium additions on the hot tearing susceptibility of magnesium-zinc alloys
P. Gunde et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
A quest for a new hot tearing criterion
D. G. Eskin et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2007)
Two-phase modelling of hot tearing in aluminium alloys using a semi-coupled approach
V. Mathier et al.
MODELLING AND SIMULATION IN MATERIALS SCIENCE AND ENGINEERING (2007)
Materials for ultra-supercritical coal-fired power plant boilers
R. Viswanathan et al.
INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2006)
TearSim:: A two-phase model addressing hot tearing formation during aluminum direct chill casting
Mohammed M'Hamdi et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2006)
Hot cracking of binary Mg-Al alloy castings
G Cao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)
Thermodynamic calculation as a tool for thixoforming alloy and process development
MB Djurdjevic et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)
Mechanical properties in the semi-solid state and hot tearing of aluminium alloys
DG Eskin et al.
PROGRESS IN MATERIALS SCIENCE (2004)
Coalescence of equiaxed grains during solidification
V Mathier et al.
MODELLING AND SIMULATION IN MATERIALS SCIENCE AND ENGINEERING (2004)
Hot-tearing susceptibility of Mg-9Al-xZn alloy
YS Wang et al.
MATERIALS LETTERS (2002)
Two-phase modeling directed toward hot tearing formation in aluminum direct chill casting
M M'Hamdi et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2002)
An understanding of the hot tearing mechanism in AZ91 magnesium alloy
YS Wang et al.
MATERIALS LETTERS (2002)
In situ observation of hot tearing formation in succinonitrile-acetone
I Farup et al.
ACTA MATERIALIA (2001)
Two-phase modeling of mushy zone parameters associated with hot tearing
I Farup et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2000)
Share Paper
