Related references
Note: Only part of the references are listed.On the recyclability of polyamide for sustainable composite structures in civil engineering
Rupinder Singh et al.
COMPOSITE STRUCTURES (2018)
In-vitro studies of SS 316 L biomedical implants prepared by FDM, vapor smoothing and investment casting
Daljinder Singh et al.
COMPOSITES PART B-ENGINEERING (2018)
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Tuan D. Ngo et al.
COMPOSITES PART B-ENGINEERING (2018)
Friction welding for the manufacturing of PA6 and ABS structures reinforced with Fe particles
Ranvijay Kumar et al.
COMPOSITES PART B-ENGINEERING (2018)
On the applicability of composite PA6-TiO2 filaments for the rapid prototyping of innovative materials and structures
Rupinder Singh et al.
COMPOSITES PART B-ENGINEERING (2018)
Graphene as biomedical sensing element: State of art review and potential engineering applications
Ranvijay Kumar et al.
COMPOSITES PART B-ENGINEERING (2018)
Weldability of thermoplastic materials for friction stir welding- A state of art review and future applications
Ranvijay Kumar et al.
COMPOSITES PART B-ENGINEERING (2018)
Additive manufacturing of multi-material structures
Amit Bandyopadhyay et al.
MATERIALS SCIENCE & ENGINEERING R-REPORTS (2018)
Three-dimensional printing of multilayered tissue engineering scaffolds
Sean M. Bittner et al.
MATERIALS TODAY (2018)
Life cycle assessment of recycled concretes: A case study in southern Italy
Francesco Colangelo et al.
SCIENCE OF THE TOTAL ENVIRONMENT (2018)
Effect of Printing Parameters on Tensile, Dynamic Mechanical, and Thermoelectric Properties of FDM 3D Printed CABS/ZnO Composites
Yah Yun Aw et al.
MATERIALS (2018)
3D Printing Technologies for Flexible Tactile Sensors toward Wearable Electronics and Electronic Skin
Changyong Liu et al.
POLYMERS (2018)
A 3D Printable Thermal Energy Storage Crystalline Gel Using Mask-Projection Stereolithography
Yuchen Mao et al.
POLYMERS (2018)
Characterizing the effect of print orientation on interface integrity of multi-material jetting additive manufacturing
Ivan Q. Vu et al.
ADDITIVE MANUFACTURING (2018)
Microstructural and Mechanical Implications of Microscaled Assembly in Droplet-based Multi-Material Additive Manufacturing
Sofiane Guessasma et al.
POLYMERS (2017)
A review of 4D printing
Farhang Momeni et al.
MATERIALS & DESIGN (2017)
Development of a multi-material additive manufacturing process for electronic devices
A. Muguruza et al.
MANUFACTURING ENGINEERING SOCIETY INTERNATIONAL CONFERENCE 2017 (MESIC 2017) (2017)
Investigations for Thermal and Electrical Conductivity of ABS-Graphene Blended Prototypes
Rupinder Singh et al.
MATERIALS (2017)
Lightweight geopolymer-based hybrid materials
Giuseppina Roviello et al.
COMPOSITES PART B-ENGINEERING (2017)
Mechanical properties and durability of mortar containing fine fraction of demolition wastes produced by selective demolition in South Italy
F. Colangelo et al.
COMPOSITES PART B-ENGINEERING (2017)
Recycling of non-metallic automotive shredder residues and coal fly-ash in cold-bonded aggregates for sustainable concrete
F. Colangelo et al.
COMPOSITES PART B-ENGINEERING (2017)
Fundamentals and applications of 3D printing for novel materials
Jian-Yuan Lee et al.
APPLIED MATERIALS TODAY (2017)
Synergistic recycling of calcined clayey sediments and water potabilization sludge as geopolymer precursors: Upscaling from binders to precast paving cement-free bricks
F. Messina et al.
CONSTRUCTION AND BUILDING MATERIALS (2017)
Experimental response of additively manufactured metallic pentamode materials confined between stiffening plates
A. Amendola et al.
COMPOSITE STRUCTURES (2016)
Recycled polyolefins waste as aggregates for lightweight concrete
Francesco Colangelo et al.
COMPOSITES PART B-ENGINEERING (2016)
Surface roughness effects on the reinforcement of cement mortars through 3D printed metallic fibers
Ilenia Farina et al.
COMPOSITES PART B-ENGINEERING (2016)
Friction welding of dissimilar plastic/polymer materials with metal powder reinforcement for engineering applications
Rupinder Singh et al.
COMPOSITES PART B-ENGINEERING (2016)
Printing soft matter in three dimensions
Ryan L. Truby et al.
NATURE (2016)
Material Evaluation and Process Optimization of CNT-Coated Polymer Powders for Selective Laser Sintering
Shangqin Yuan et al.
POLYMERS (2016)
On the additive manufacturing, post-tensioning and testing of bi-material tensegrity structures
A. Amendola et al.
COMPOSITE STRUCTURES (2015)
Low temperature alkaline activation of weathered fly ash: Influence of mineral admixtures on early age performance
Francesco Messina et al.
CONSTRUCTION AND BUILDING MATERIALS (2015)
Mechanical Property Optimization of FDM PLA in Shear with Multiple Objectives
Jonathan Torres et al.
JOM (2015)
Recycling of MSWI fly ash by means of cementitious double step cold bonding pelletization: Technological assessment for the production of lightweight artificial aggregates
Francesco Colangelo et al.
JOURNAL OF HAZARDOUS MATERIALS (2015)
Hybrid Deposition Manufacturing: Design Strategies for Multimaterial Mechanisms Via Three-Dimensional Printing and Material Deposition
Raymond R. Ma et al.
JOURNAL OF MECHANISMS AND ROBOTICS-TRANSACTIONS OF THE ASME (2015)
Strong, lightweight, and recoverable three-dimensional ceramic nanolattices
Lucas R. Meza et al.
SCIENCE (2014)
Ultralight, Ultrastiff Mechanical Metamaterials
Xiaoyu Zheng et al.
SCIENCE (2014)
Elastic measurements on macroscopic three-dimensional pentamode metamaterials
Robert Schittny et al.
APPLIED PHYSICS LETTERS (2013)
Synthesis and Characterizations of Melamine-Based Epoxy Resins
Laura Ricciotti et al.
INTERNATIONAL JOURNAL OF MOLECULAR SCIENCES (2013)
On the practicability of pentamode mechanical metamaterials
Muamer Kadic et al.
APPLIED PHYSICS LETTERS (2012)
Hybrid Lattice Particle Modelling Approach for Polymeric Materials Subject to High Strain Rate Loads
Ge Wang et al.
POLYMERS (2010)
Poly(lactic acid):: plasticization and properties of biodegradable multiphase systems
O Martin et al.
POLYMER (2001)
Share Paper
