Related references
Note: Only part of the references are listed.Cold spray deposition for additive manufacturing of freeform structural components compared to selective laser melting
Sara Bagherifard et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Influence of hot isostatic pressing on the performance of aluminum alloy fabricated by ultrasonic additive manufacturing
M. N. Gussev et al.
SCRIPTA MATERIALIA (2018)
Influence of feedstock powder and cold spray processing parameters on microstructure and mechanical properties of Ti-6Al-4V cold spray depositions
Venkata Satish Bhattiprolu et al.
SURFACE & COATINGS TECHNOLOGY (2018)
Thermo-mechanical post-treatment: A strategic approach to improve microstructure and mechanical properties of cold spray additively manufactured composites
N. H. Tariq et al.
MATERIALS & DESIGN (2018)
Cold spray under the banner of thermal spray in the whirlwind of additive manufacturing
Michel Jeandin
SURFACE ENGINEERING (2018)
Microstructure and mechanical anisotropy of additively manufactured cold spray copper deposits
Shuo Yin et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Fatigue properties of a titanium alloy (Ti-6Al-4V) fabricated via electron beam melting (EBM): Effects of internal defects and residual stress
Nikolas Hrabe et al.
INTERNATIONAL JOURNAL OF FATIGUE (2017)
Effect of multi-pass friction stir processing on the microstructure, mechanical and wear properties of AA5083/ZrO2 nanocomposites
Seyed Sajad Mirjavadi et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2017)
Influence of TiO2 nanoparticles incorporation to friction stir welded 5083 aluminum alloy on the microstructure, mechanical properties and wear resistance
Seyed Sajad Mirjavadi et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2017)
Statistically Guided Development of Laser-Assisted Cold Spray for Microstructural Control of Ti-6Al-4V
Aaron M. Birt et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2017)
Cold gas dynamic spray additive manufacturing today: Deposit possibilities, technological solutions and viable applications
R. N. Raoelison et al.
MATERIALS & DESIGN (2017)
New two-tier low pressure turbine for heavy duty steam turbines
A. E. Zaryankin et al.
INTERNATIONAL CONFERENCE PROBLEMS OF THERMAL PHYSICS AND POWER ENGINEERING (PTPPE-2017) (2017)
Laser and electron-beam powder-bed additive manufacturing of metallic implants: A review on processes, materials and designs
Swee Leong Sing et al.
JOURNAL OF ORTHOPAEDIC RESEARCH (2016)
Cold spraying - A materials perspective
H. Assadi et al.
ACTA MATERIALIA (2016)
Mechanical behavior of additive manufactured, powder-bed laser-fused materials
Todd M. Mower et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
Influence of temperature, pressure, and cooling rate during hot isostatic pressing on the microstructure of an SX Ni-base superalloy
L. Mujica Roncery et al.
MATERIALS & DESIGN (2016)
Combination of electroforming and cold gas dynamic spray for fabrication of rotational moulds: feasibility study
Fernando Ortega et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Investigation of the effect of Al-8B master alloy and strain-induced melt activation process on dry sliding wear behavior of an Al-Zn-Mg-Cu alloy
Seyed Sajad Mirjavadi et al.
MATERIALS & DESIGN (2014)
Potential of cold gas dynamic spray as additive manufacturing technology
A. Sova et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)
Mechanical and Microstructural Characterization of Cold-Sprayed Ti-6Al-4V After Heat Treatment
P. Vo et al.
JOURNAL OF THERMAL SPRAY TECHNOLOGY (2013)
Study on Tool Wear and Chip Formation during Drilling Carbon Fiber Reinforced Polymer (CFRP)/Titanium Alloy (Ti6Al4V) Stacks
M. SenthilKumar et al.
INTERNATIONAL CONFERENCE ON DESIGN AND MANUFACTURING (ICONDM2013) (2013)
Powder Processing and Coating Heat Treatment on Cold Sprayed Ti-6Al-4V Alloy
Wilson Wong et al.
THERMEC 2011, PTS 1-4 (2012)
The effect of structure on mechanical behavior of VT6 titanium alloy under shock loading
A. A. Sarkeeva et al.
LETTERS ON MATERIALS (2012)
Influence of Helium and Nitrogen Gases on the Properties of Cold Gas Dynamic Sprayed Pure Titanium Coatings
Wilson Wong et al.
JOURNAL OF THERMAL SPRAY TECHNOLOGY (2011)
Evaluation of Titanium Alloys Fabricated Using Rapid Prototyping Technologies-Electron Beam Melting and Laser Beam Melting
Mari Koike et al.
MATERIALS (2011)
From Particle Acceleration to Impact and Bonding in Cold Spraying
Tobias Schmidt et al.
JOURNAL OF THERMAL SPRAY TECHNOLOGY (2009)
Influence of hot isostatic pressing on the fracture transitions in the fine grain MAR-M247 superalloys
HY Bor et al.
MATERIALS CHEMISTRY AND PHYSICS (2004)
Hot Isostatic Pressing (HIP) technology and its applications to metals and ceramics
MH Bocanegra-Bernal
JOURNAL OF MATERIALS SCIENCE (2004)