Related references
Note: Only part of the references are listed.Micro-channels by Nd:YAG laser beam machining: fabrication, microstructures, and micro-hardness profiles
Naveed Ahmed et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
A comparison of laser beam machining of micro-channels under dry and wet mediums
Saied Darwish et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
Grit Blasting for Removal of Recast Layer from EDM Process on Inconel 718 Shaft: An Evaluation of Surface Integrity
Jonas Holmberg et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2016)
Machinability of Nickel-Based Superalloy by Abrasive Water Jet Machining
M. Uthayakumar et al.
MATERIALS AND MANUFACTURING PROCESSES (2016)
Additive manufacturing of functional elements on sheet metal
Adam Schaub et al.
LASER ASSISTED NET SHAPE ENGINEERING 9 INTERNATIONAL CONFERENCE ON PHOTONIC TECHNOLOGIES PROCEEDINGS OF THE LANE 2016 (2016)
Machining Characteristics of Inconel 718 by Sinking-EDM and Wire-EDM
L. Li et al.
MATERIALS AND MANUFACTURING PROCESSES (2015)
Surface integrity evolution and machining efficiency analysis of W-EDM of nickel-based alloy
L. Li et al.
APPLIED SURFACE SCIENCE (2014)
Cutting temperatures during hard turning-Measurements and effects on white layer formation in AISI 52100
S. B. Hosseini et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2014)
Machining Performance of Inconel 718 Using High Current Density Electrical Discharge Milling
Fei Wang et al.
MATERIALS AND MANUFACTURING PROCESSES (2013)
CO2 laser cut quality of Inconel 718 nickel - based superalloy
Ahmet Hascalik et al.
OPTICS AND LASER TECHNOLOGY (2013)
Topology optimization approaches A comparative review
Ole Sigmund et al.
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2013)
Surface integrity characteristics in wire-EDM of inconel 718 at different discharge energy
L. Li et al.
PROCEEDINGS OF THE SEVENTEENTH CIRP CONFERENCE ON ELECTRO PHYSICAL AND CHEMICAL MACHINING (ISEM) (2013)
Parametric effects on grit embedment and surface morphology in an innovative hybrid waterjet cleaning process for alpha case removal from titanium alloys
L. Huang et al.
PROCEEDINGS OF THE SEVENTEENTH CIRP CONFERENCE ON ELECTRO PHYSICAL AND CHEMICAL MACHINING (ISEM) (2013)
Characterisation of abrasive water-jet process for pocket milling in Inconel 718
G. A. Escobar-Palafox et al.
FIFTH CIRP CONFERENCE ON HIGH PERFORMANCE CUTTING 2012 (2012)
Surface integrity in material removal processes: Recent advances
I. S. Jawahir et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2011)
Experimental Study of the Slot Overlapping and Tool Path Variation Effect in Abrasive Waterjet Milling
A. Alberdi et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2011)
Experimental research on machining characteristics of SiC ceramic with end electric discharge milling
Renjie Ji et al.
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2011)
High-Speed End Electric Discharge Milling of Silicon Carbide Ceramics
Renjie Ji et al.
MATERIALS AND MANUFACTURING PROCESSES (2011)
Thermal Characteristics in the Cutting of Inconel 718 Superalloy Using CW Nd:YAG Laser
D. G. Ahn et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2010)
Effect of Traverse Speed on Abrasive Waterjet Machining of Age Hardened Inconel 718 Nickel-Based Superalloy
Mustafa Ay et al.
MATERIALS AND MANUFACTURING PROCESSES (2010)
Thermal modeling of the material removal rate and surface roughness for die-sinking EDM
K. Salonitis et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2009)
Waterjet-An innovative tool for manufacturing
Janet Folkes
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
Surface modification by electrical discharge machining: A review
Sanjeev Kumar et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
Investigation of the effect of process parameters on the formation and characteristics of recast layer in wire-EDM of Inconel 718
Thomas R. Newton et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)
Influence of cutting parameters on surface characteristics of cut section in cutting of Inconel 718 sheet using CW Nd:YAG laser
Dong-Gyu Ahn et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2009)
Workpiece surface roughness and integrity after WEDM of Ti-6Al-4V and Inconel 718 using minimum damage generator technology
D. K. Aspinwall et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2008)
Laser beam machining - A review
Avanish Kumar Dubey et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)
A review on current research trends in electrical discharge machining (EDM)
Norliana Mohd Abbas et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2007)
A semi-empirical approach for residual stresses in electric discharge machining (EDM)
Bulent Ekmekci et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2006)
State of the art electrical discharge machining (EDM)
KH Ho et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2003)