Related references
Note: Only part of the references are listed.Microstructure design and mechanical properties in a near-α Ti-4Mo alloy
Z. Tarzimoghadam et al.
ACTA MATERIALIA (2015)
Graded microstructure and mechanical properties of additive manufactured Ti-6Al-4V via electron beam melting
Xipeng Tan et al.
ACTA MATERIALIA (2015)
Additive manufacturing of strong and ductile Ti-6Al-4V by selective laser melting via in situ martensite decomposition
W. Xu et al.
ACTA MATERIALIA (2015)
An experimental and simulation study on build thickness dependent microstructure for electron beam melted Ti-6Al-4V
Xipeng Tan et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2015)
Linear complexions: Confined chemical and structural states at dislocations
M. Kuzmina et al.
SCIENCE (2015)
Fabrication and microstructural characterisation of additive manufactured Ti-6Al-4V parts by electron beam melting This paper reports that the microstructure and micro-hardness of an EMB part is thickness dependent
Yihong Kok et al.
VIRTUAL AND PHYSICAL PROTOTYPING (2015)
Engineering science aspects of the Hall-Petch relation
Ronald W. Armstrong
ACTA MECHANICA (2014)
Metal Additive Manufacturing: A Review
William E. Frazier
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2014)
Atom probe tomography for advanced metallization
D. Mangelinck et al.
MICROELECTRONIC ENGINEERING (2014)
Developing Gradient Metal Alloys through Radial Deposition Additive Manufacturing
Douglas C. Hofmann et al.
SCIENTIFIC REPORTS (2014)
Atom probe tomographic study of L10 martensite in a Pt-modified NiCoCrAlYTa bond coating
Xipeng Tan et al.
CORROSION SCIENCE (2013)
Loss of coherency and interphase α/β angular deviation from the Burgers orientation relationship in a Ti-6Al-4V alloy compressed at 800 °C
M. Cabibbo et al.
JOURNAL OF MATERIALS SCIENCE (2013)
Structural phase transformations in metallic grain boundaries
Timofey Frolov et al.
NATURE COMMUNICATIONS (2013)
Metal Fabrication by Additive Manufacturing Using Laser and Electron Beam Melting Technologies
Lawrence E. Murr et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2012)
Al-Ti-V (Aluminum-Titanium-Vanadium)
V. Raghavan
JOURNAL OF PHASE EQUILIBRIA AND DIFFUSION (2012)
Evaluation of microstructural development in electron beam melted Ti-6Al-4V
A. Safdar et al.
MATERIALS CHARACTERIZATION (2012)
Intergrowth of P phase with mu phase in a Ru-containing single-crystal Ni-based superalloy
X. P. Tan et al.
PHILOSOPHICAL MAGAZINE LETTERS (2012)
The Phase Behavior of Interfaces
Martin P. Harmer
SCIENCE (2011)
The Origin of Microstructural Diversity, Texture, and Mechanical Properties in Electron Beam Melted Ti-6Al-4V
S. S. Al-Bermani et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2010)
Simultaneous Segregation at Coherent and Semicoherent Heterophase Interfaces
Aniruddha Biswas et al.
PHYSICAL REVIEW LETTERS (2010)
Microstructures and mechanical properties of electron beam-rapid manufactured Ti-6Al-4V biomedical prototypes compared to wrought Ti-6Al-4V
L. E. Murr et al.
MATERIALS CHARACTERIZATION (2009)
Experimental study of dislocation mobility in a Ti-6Al-4V alloy
P. Castany et al.
ACTA MATERIALIA (2007)
Interfacial segregation at Cu-rich precipitates in a high-strength low-carbon steel studied on a sub-nanometer scale
D Isheim et al.
ACTA MATERIALIA (2006)
In situ observations of lattice expansion and transformation rates of α and β phases in Ti-6Al-4V
JW Elmer et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2005)
Nanoscale studies of segregation at coherent heterophase interfaces in α-Fe based systems
D Isheim et al.
SURFACE AND INTERFACE ANALYSIS (2004)
Share Paper
