Related references
Note: Only part of the references are listed.Prevention of porosity by oxygen addition in fibre laser and fibre laser-GMA hybrid welding
L. Zhao et al.
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2014)
Quantifying the effect of porosity on the evolution of deformation and damage in Sn-based solder joints by X-ray microtomography and microstructure-based finite element modeling
E. Padilla et al.
ACTA MATERIALIA (2012)
Fatigue and Damage in Structural Materials Studied by X-Ray Tomography
Philip J. Withers et al.
ANNUAL REVIEW OF MATERIALS RESEARCH, VOL 42 (2012)
Three-dimensional characterisation and modelling of small fatigue corner cracks in high strength Al-alloys
Henry Proudhon et al.
COMPTES RENDUS PHYSIQUE (2012)
Material defects as the basis of fatigue design
Yukitaka Murakami
INTERNATIONAL JOURNAL OF FATIGUE (2012)
In situ observation of ductile fracture using X-ray tomography technique
H. Toda et al.
ACTA MATERIALIA (2011)
Statistical assessment of fatigue crack initiation from sub-surface hydrogen micropores in high-quality die-cast aluminum
Hiroyuki Toda et al.
ACTA MATERIALIA (2011)
Microtomographic study and finite element analysis of the porosity harmfulness in a cast aluminium alloy
N. Vanderesse et al.
INTERNATIONAL JOURNAL OF FATIGUE (2011)
Damage observation in a high-manganese austenitic TWIP steel by synchrotron radiation computed tomography
J. Lorthios et al.
SCRIPTA MATERIALIA (2010)
Quantification of the interaction within defect populations on fatigue behavior in an aluminum alloy
P. Li et al.
ACTA MATERIALIA (2009)
Healing behavior of preexisting hydrogen micropores in aluminum alloys during plastic deformation
H. Toda et al.
ACTA MATERIALIA (2009)
Three-dimensional fatigue crack growth behavior in an aluminum alloy investigated with in situ high-resolution synchrotron X-ray microtomography
H. Zhang et al.
ACTA MATERIALIA (2009)
Direct measurement procedure for three-dimensional local crack driving force using synchrotron X-ray microtomography
H. Toda et al.
ACTA MATERIALIA (2008)
Recent advances in X-ray microtomography applied to materials
S. R. Stock
INTERNATIONAL MATERIALS REVIEWS (2008)
Three-dimensional visualization of ductile fracture in an Al-Si alloy by high-resolution synchrotron X-ray microtomography
L. Qian et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Three-dimensional visualization of the interaction between fatigue crack and micropores in an aluminum alloy using synchrotron X-ray microtomography
H. Zhang et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2007)
The influence of porosity on the fatigue crack growth behavior of Ti-6Al-4V laser welds
L. W. Tsay et al.
JOURNAL OF MATERIALS SCIENCE (2006)
Three-dimensional visualisation of fatigue cracks in metals using high resolution synchrotron X-ray micro-tomography
J. Y. Buffiere et al.
MATERIALS SCIENCE AND TECHNOLOGY (2006)
In situ analysis of cracks in structural materials using synchrotron X-ray tomography and diffraction
A Steuwer et al.
NUCLEAR INSTRUMENTS & METHODS IN PHYSICS RESEARCH SECTION B-BEAM INTERACTIONS WITH MATERIALS AND ATOMS (2006)
Fatigue crack propagation:: In situ visualization using X-ray microtomography and 3D simulation using the extended finite element method
E Ferrié et al.
ACTA MATERIALIA (2006)
Hot cracking of welds on heat treatable aluminium alloys
CM Cheng et al.
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2005)
A 3D measurement procedure for internal local crack driving forces via synchrotron X-ray microtomography
H Toda et al.
ACTA MATERIALIA (2004)
High resolution X-ray tomography of short fatigue crack nucleation in austempered ductile cast iron
TJ Marrow et al.
INTERNATIONAL JOURNAL OF FATIGUE (2004)
Weldability of 1.6 mm thick aluminium alloy 5182 sheet by single and dual beam Nd:YAG laser welding
MG Deutsch et al.
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2003)
Study of the interaction of a short fatigue crack with grain boundaries in a cast Al alloy using X-ray microtomography
W Ludwig et al.
ACTA MATERIALIA (2003)
Experimental study of porosity and its relation to fatigue mechanisms of model Al-Si7-Mg0.3 cast Al alloys
JY Buffière et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2001)
Problems and solutions in deep penetration laser welding
A Matsunawa
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2001)
Laser beam welding of wrought aluminium alloys
JC Ion
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2000)