Related references
Note: Only part of the references are listed.Mechanics of high speed cutting with curvilinear edge tools
Yigit Karpat et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)
Investigation of tool wear and cutting force in cryogenic machining using design of experiments
K. V. B. S. Kalyan Kumar et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Improving tool life using cryogenic cooling
Ahsan Ali Khan et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
An experimental investigation of hot-machining to predict tool life
K. P. Maity et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Analysis of forces in ultrasonically assisted turning
N. Ahmed et al.
JOURNAL OF SOUND AND VIBRATION (2007)
Evaluating various factors for turning of Adamite
V. S. Sharma et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2007)
PCBN tool wear modes and mechanisms in finish hard turning
Cora Lahiff et al.
ROBOTICS AND COMPUTER-INTEGRATED MANUFACTURING (2007)
A study on ultrasonic vibration cutting of low alloy steel
Chandra Nath M. Rahman et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)
An investigation of cutting forces and surface damage in high-speed turning of Inconel 718
R. S. Pawade et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)
High speed MQL finish-turning of Inconel 718 with different coated tools
Y. Kamata et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)
Analysis of an equivalent tool face for the cutting speed range prediction of complex grooved tools
L. Deshayes
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)
Effectiveness of cryogenic machining with modified tool holder
Mirghani I. Ahmed et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)
Growth of tool wear in turning of Ti-6Al-4V alloy under cryogenic cooling
K. A. Venugopal et al.
WEAR (2007)
Cutting temperature, tool wear, surface roughness and dimensional deviation in turning AISI-4037 steel under cryogenic condition
N. R. Dhar et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2007)
Study on lubricating characteristic and tool wear with water vapor as coolant and lubricant in green cutting
Junyan Liu et al.
WEAR (2007)
Influence of the direction and flow rate of the cutting fluid on tool life in turning process of AISI 1045 steel
Anselmo Eduardo Diniz et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2007)
The effect of cutting speed and cutting tool geometry on machinability properties of nickel-base Inconel 718 super alloys
Muammer Nalbant et al.
MATERIALS & DESIGN (2007)
Performance evaluation of cryogenically treated tungsten carbide tools in turning
A. Y. L. Yong et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2006)
Laser-assisted machining of Inconel 718 with an economic analysis
Mark Anderson et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2006)
Minimal quantity lubrication in turning: Effect on tool wear
A Attanasio et al.
WEAR (2006)
Effect of minimum quantity lubrication (MQL) on tool wear and surface roughness in turning AISI-4340 steel
NR Dhar et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2006)
Investigation of cutting conditions and cutting edge preparations for enhanced compressive subsurface residual stress in the hard turning of bearing steel
J Hua et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2006)
Key improvements in the machining of difficult-to-cut aerospace superalloys
EO Ezugwu
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2005)
Progressive tool-wear in machining with coated grooved tools and its correlation with cutting temperature
PC Wanigarathne et al.
WEAR (2005)
The effect of chamfer angle of polycrystalline cubic boron nitride cutting tool on the cutting forces and the tool stresses in finishing hard turning of AISI 52100 steel
A Kurt et al.
MATERIALS & DESIGN (2005)
Machining of nickel-base, Inconel 718, alloy with ceramic tools under finishing conditions with various coolant supply pressures
EO Ezugwu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2005)
Effect of feed rate, workpiece hardness and cutting edge on subsurface residual stress in the hard turning of bearing steel using chamfer plus hone cutting edge geometry
J Hua et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2005)
Machining hardmetal with CVD diamond direct coated ceramic tools: effect of tool edge geometry
FA Almeida et al.
DIAMOND AND RELATED MATERIALS (2005)
Some effects of cutting edge preparation and geometric modifications when turning INCONEL 718™ at high cutting speeds
RT Coelho et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
Effect of high-pressure coolant supply when machining nickel-base, Inconel 718, alloy with coated carbide tools
EO Ezugwu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
Finite element analysis of ultrasonically assisted turning of Inconel 718
AV Mitrofanov et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
Hybrid machining of Inconel 718
ZY Wang et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2003)
Analytical prediction of the chip rack-flow angle in machining with restricted contact grooved tools
N Fang et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2003)
Effect of chamfer angle on wear of PCBN cutting tool
JM Zhou et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2003)
Ultrasonically assisted turning of aviation materials
VI Babitsky et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)
Microstructure of cryogenic treated M2 tool steel
JY Huang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)
Performance evaluation of cryogenically treated tungsten carbide cutting tool inserts
KHW Seah et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2003)
A study of tool life in hot machining using artificial neural networks and regression analysis method
N Tosun et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2002)
The influence of cryogenic cooling on tool wear, dimensional accuracy and surface finish in turning AISI 1040 and E4340C steels
NR Dhar et al.
WEAR (2001)
Beneficial effects of cryogenic cooling over dry and wet machining on tool wear and surface finish in turning AISI 1060 steel
S Paul et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)
Development of a practical ultrasonic vibration cutting tool system
M Jin et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)
Cryogenic treatment to augment wear resistance of tool and die steels
DM Lal et al.
CRYOGENICS (2001)
Mechanics of machining with chamfered tools
T Ren et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2000)
A new model and analysis of orthogonal machining with an edge-radiused tool
J Manjunathaiah et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2000)
Share Paper
