Related references
Note: Only part of the references are listed.Characterization of Ferrite in Tempered Martensite of Modified 9Cr-1Mo Steel Using the Electron Backscattered Diffraction Technique
C. R. Das et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2011)
Finite element analysis of type IV cracking in 2.25Cr-1Mo steel weldment based on micro-mechanistic approach
Sunil Goyal et al.
PHILOSOPHICAL MAGAZINE (2011)
Precipitation behavior of Laves phase in 10%Cr steel X12CrMoWVNbN10-1-1 during short-term creep exposure
Huiran Cui et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
EFFECT OF BORON ON MICROSTRUCTURE AND MECHANICAL PROPERTIES OF HOT-ROLLED Nb-ADDED HSLA H-SECTION STEEL
Zuocheng Wang et al.
INTERNATIONAL JOURNAL OF MODERN PHYSICS B (2009)
Type IV Cracking Susceptibility in Weld Joints of Different Grades of Cr-Mo Ferritic Steel
K. Laha et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2009)
Microstructure and long-term creep properties of 9-12% Cr steels
J. Hald
INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2008)
Refinement of austenite grain in carbon steel by addition of titanium and boron
Masayoshi Sasaki et al.
ISIJ INTERNATIONAL (2008)
Suppression of Type IV fracture and improvement of creep strength of 9Cr steel welded joints by boron addition
Fujio Abe et al.
INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2007)
Effect of block size on the strength of lath martensite in low carbon steels
S. Morito et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)
Type IV cracking in ferritic power plant steels
J. A. Francis et al.
MATERIALS SCIENCE AND TECHNOLOGY (2006)
Effect of normalization temperature on the creep strength of modified 9Cr-1Mo steel
T. C. Totemeier et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2006)
Suppressing type IV failure via modification of heat affected zone microstructures using high boron content in 9Cr heat resistant steel welded joints
M Kondo et al.
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2006)
Crystallographic features of lath martensite in low-carbon steel
H Kitahara et al.
ACTA MATERIALIA (2006)
Creep damage evaluation of 9Cr-1Mo-V-Nb steel welded joints showing Type IV fracture
T Watanabe et al.
INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2006)
Influence of heat treatment on formation behavior of boron nitride inclusions in P122 heat resistant steel
Kazuyuki Sakuraya et al.
ISIJ INTERNATIONAL (2006)
Development of new nano-particle-strengthened martensitic steels
RL Klueh et al.
SCRIPTA MATERIALIA (2005)
A trigger of type IV damage and a new heat treatment procedure to suppress it. Microstructural investigations of long-term ex-service Cr-Mo steel pipe elbows
H Tezuka et al.
INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2005)
High temperature creep flow and damage properties of the weakest area of 9Cr1Mo-NbV martensitic steel weldments
V Gaffard et al.
ISIJ INTERNATIONAL (2005)
Effect of carbon concentration on precipitation behavior of M23C6 carbides and MX carbonitrides in martensitic 9Cr steel during heat treatment
M Taneike et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2004)
A study on the improvement of the fracture toughness of Ll2-type Cu-added zirconium trialuminide intermetallics synthesized by mechanical alloying
SH Lee et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2004)
Stabilization of martensitic microstructure in advanced 9Cr steel during creep at high temperature
F Abe et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2004)
Analysis of factors affecting type IV cracking in welded joints of high chromium ferritic heat resistant steels
D Li et al.
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2003)
Two-phase separation of primary MX carbonitride during tempering in creep resistant 9Cr1MoVNb steel
K Suzuki et al.
ISIJ INTERNATIONAL (2003)
Precipitate stability in creep resistant ferritic steels - Experimental investigations and modelling
J Hald et al.
ISIJ INTERNATIONAL (2003)
Analysis of the creep behaviour of modified P91 (9Cr-1Mo-NbV) welds
S Spigarelli et al.
MATERIALS & DESIGN (2002)
Creep properties affected by morphology of MX in high-Cr ferritic steels
K Yamada et al.
ISIJ INTERNATIONAL (2001)
Share Paper
