Related references
Note: Only part of the references are listed.Investigation of mechanical properties of Cu/SiC composite fabricated by FSP: Effect of SiC particles' size and volume fraction
M. Barmouz et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
Producing of AZ91/SiC composite by friction stir processing (FSP)
Parviz Asadi et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2010)
Producing Ultrafine-Grained AZ91 from As-Cast AZ91 by FSP
P. Asadi et al.
MATERIALS AND MANUFACTURING PROCESSES (2010)
A novel approach for development of surface nanocomposite by friction stir processing
B. Zahmatkesh et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
Effect of Processing Parameters on Microstructure and Mechanical Properties of an Al-Al11Ce3-Al2O3 In-Situ Composite Produced by Friction Stir Processing
C. F. Chen et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2010)
Effect of an interphase layer on the dynamic stress concentration in a Mg-matrix surrounding a SiC-particle
R. Paskaramoorthy et al.
COMPOSITE STRUCTURES (2009)
Microstructures and mechanical properties of Al/Al2O3 surface nano-composite layer produced by friction stir processing
A. Shafiei-Zarghani et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)
Recrystallization mechanism of as-cast AZ91 magnesium alloy during hot compressive deformation
S. W. Xu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)
Effect of Friction Stir Processing Procedures on Microstructure and Mechanical Properties of Mg-Al-Zn Casting
A. H. Feng et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2009)
Dry sliding wear behaviour of plasma electrolytic oxidation coated AZ91 cast magnesium alloy
P. Bala Srinivasan et al.
WEAR (2009)
Effect of submicron size Al2O3 particulates on microstructural and tensile properties of elemental Mg
S. F. Hassan et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2008)
Mechanical properties and microstructure of SiC-reinforced Mg-(2,4)A1-1Si nanocomposites fabricated by ultrasonic cavitation based solidification processing
G. Cao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Friction stir processing technology: A review
Z. Y. Ma
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2008)
Dry sliding wear behavior of magnesium alloys
J. An et al.
WEAR (2008)
Friction stir processing of commercial AZ31 magnesium alloy
B. M. Darras et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)
Superplastic behaviour of friction stir processed AZ91 magnesium alloy produced by high pressure die cast
P. Cavaliere et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)
Enhanced mechanical properties of Mg-Al-Zn cast alloy via friction stir processing
A. H. Feng et al.
SCRIPTA MATERIALIA (2007)
Effect of friction stir processing with SiC particles on microstructure and hardness of AZ31
Y. Morisada et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)
Mg based nano-composites fabricated by friction stir processing
CJ Lee et al.
SCRIPTA MATERIALIA (2006)
Microstructure and tensile properties of Ti6Al4V/AM60B magnesium matrix composite
HZ Ye et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2005)
Study of selected properties of magnesium alloy AZ91 after heat treatment and forming
L Cizek et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
Avalanches in fine, cohesive powders
JM Valverde et al.
PHYSICAL REVIEW E (2000)
Sliding wear map for the magnesium alloy Mg-9Al-0.9 Zn (AZ91)
H Chen et al.
WEAR (2000)
Share Paper
