Related references
Note: Only part of the references are listed.Microstructural, mechanical and electrical characterization of directionally solidified Al-Si-Mg eutectic alloy
Yusuf Kaygisiz et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2015)
Twin Roll Casting of Al-Mg Alloy with High Added Impurity Content
S. Kumar et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2014)
An Evaluation of Primary Dendrite Trunk Diameters in Directionally Solidified Al-Si Alloys
S. N. Tewari et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2014)
Influence of cooling rate on the Fe intermetallic formation in an AA6063 Al alloy
A. Verma et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2013)
Interrelation of cell spacing, intermetallic compounds and hardness on a directionally solidified Al-1.0Fe-1.0Ni alloy
Manuel V. Cante et al.
MATERIALS & DESIGN (2013)
Effect of iron on the microstructure and mechanical property of Al-Mg-Si-Mn and Al-Mg-Si diecast alloys
Shouxun Ji et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
Numerical and experimental investigation of microporosity formation in a ternary Al-Cu-Si alloy
Ivaldo L. Ferreira et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2010)
Dendritic Arm Spacing Affecting Mechanical Properties and Wear Behavior of Al-Sn and Al-Si Alloys Directionally Solidified under Unsteady-State Conditions
Kleber S. Cruz et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2010)
Interfacial heat transfer coefficients and solidification of an aluminum alloy in a rotary continuous caster
Noe Cheung et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2009)
Cellular growth during transient directional solidification of hypoeutectic Al-Fe alloys
Pedro R. Goulart et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2009)
Corrosion behaviour of aluminium in copper containing environment
I. Bakos et al.
CORROSION SCIENCE (2008)
Cellular/dendritic transition and microstructure evolution during transient directional solidification of Pb-Sb alloys
Daniel M. Rosa et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2008)
Microstructural development in Al-Ni alloys directionally solidified under unsteady-state conditions
Manuel V. Cante et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2008)
Copper content and cooling rate effects over second phase particles behavior in industrial aluminum-silicon alloy 319
G. Garcia-Garcia et al.
MATERIALS & DESIGN (2007)
Mechanical properties as a function of microstructure and solidification thermal variables of Al-Si castings
PR Goulart et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)
Parameters controlling the performance of AA319-type alloys Part I. Tensile properties
Z Li et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2004)
Macrostructural and microstructural development in Al-Si alloys directionally solidified under unsteady-state conditions
MD Peres et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2004)
Age-hardening behavior of cast Al-Si base alloy
RX Li et al.
MATERIALS LETTERS (2004)
In-situ synthesis of Mg2Si intermetallics via powder metallurgy process
K Kondoh et al.
MATERIALS TRANSACTIONS (2003)
Strength-ductility behaviour of Al-Si-Cu-Mg casting alloys in T6 temper
CH Caceres et al.
INTERNATIONAL JOURNAL OF CAST METALS RESEARCH (2003)
Directional solidification of aluminium -: copper alloys
M Gündüz et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2002)
The effect of free-floating dendrites and convection on macrosegregation in direct chill cast aluminum alloys Part II: predictions for Al-Cu and Al-Mg alloys
CJ Vreeman et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2000)
Share Paper
