Related references
Note: Only part of the references are listed.Mechanisms of enhanced heterogeneous nucleation during solidification in binary Al-Mg alloys
H-T. Li et al.
ACTA MATERIALIA (2012)
Synthesis of Al-TiAl3 compound by reactive deposition of molten Al droplets and Ti powders
Peng-yun Wang et al.
PROGRESS IN NATURAL SCIENCE-MATERIALS INTERNATIONAL (2011)
Structural, mechanical and tribological properties of A356 aluminium alloy reinforced with Al2O3, SiC and SiC plus graphite particles
Aleksandar Vencl et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2010)
Micro structural features and mechanical properties of Al-Al3Ti composite fabricated by in-situ powder metallurgy route
V. Abbasi Chianeh et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2009)
Surface modifications of Al-Zn-Mg alloy using combined EDM with ultrasonic machining and addition of TiC particles into the dielectric
Yuan-Feng Chen et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
Prediction of the flow stress of 6061 Al-15% SiC - MMC composites using adaptive network based fuzzy inference system
V. Kalaichelvi et al.
MATERIALS & DESIGN (2009)
The surface treatment influence on the fatigue crack propagation of Al 7050-T7451 alloy
A. L. M. Carvalho et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)
Development of high-performance A356/nano-Al2O3 composites
A. Mazahery et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)
Preparation of TiAl3-Al composite coating by cold spraying
Shen Li et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2009)
Sliding wear behaviour of T6 treated A356-TiB2 in-situ composites
A. Mandal et al.
WEAR (2009)
Thermodynamic analysis of the formation of in-situ reinforced phases in cast Al-4.5Cu alloy
Liang Yanfeng et al.
JOURNAL OF WUHAN UNIVERSITY OF TECHNOLOGY-MATERIALS SCIENCE EDITION (2008)
Study on damping capacity of aluminum composite reinforced with in situ TiAl3 rod
Yijie Zhang et al.
MATERIALS & DESIGN (2008)
Thermoanalytical and metallographical investigations on the synthesis of TiAl3 from elementary powders
Tao Wang et al.
MATERIALS CHEMISTRY AND PHYSICS (2006)
In situ investigation of the crystallization kinetics and the mechanism of grain refinement in aluminum alloys
N Iqbal et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)
Solidification of high-Cr white cast iron-WC particle reinforced composites
K Kambakas et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2005)
Study on bulk aluminum matrix nano-composite fabricated by ultrasonic dispersion of nano-sized SiC particles in molten aluminum alloy
Y Yang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2004)
The effect of heat treatment at 500-655 °C on the microstructure and properties of mechanically alloyed Al-Ti-O based material
IC Barlow et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)
Ab initio calculation of the formation energies of L12, D022, D023 and one dimensional long period structures in TiAl3 compound
C Colinet et al.
INTERMETALLICS (2002)
Wettability and phase formation in TiC/Al-alloys assemblies
EA Aguilar et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2002)
Thermal stability and its effects on the mechanical properties of rapidly solidified Al-Ti alloys
JM Wu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2000)
Microstructure and heterogeneous nucleation phenomena in cast SiC particles reinforced magnesium composite
Y Cai et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2000)
Share Paper
