Related references
Note: Only part of the references are listed.Kerf taper and delamination damage minimization of FRP hybrid composites under abrasive water-jet machining
Irina M. M. Wong et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Investigation on delamination and flexural properties in drilling of carbon nanotube/polymer composites
Hossein Heidary et al.
COMPOSITE STRUCTURES (2018)
Investigation on performance of abrasive water jet in machining hybrid composites
R. Selvama et al.
MATERIALS AND MANUFACTURING PROCESSES (2017)
Recent advances in twist drill design for composite machining: A critical review
Sikiru Oluwarotimi Ismail et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2017)
Experimental study of delamination and kerf geometry of carbon epoxy composite machined by abrasive water jet
Ajit Dhanawade et al.
JOURNAL OF COMPOSITE MATERIALS (2017)
Surface and machining induced damage characterization of abrasive water jet milled carbon/epoxy composite specimens and their impact on tensile behavior
Akshay Hejjaji et al.
WEAR (2017)
Effect of water absorption on Mode I interlaminar fracture toughness of flax/basalt reinforced vinyl ester hybrid composites
F. A. Almansour et al.
COMPOSITE STRUCTURES (2017)
Influence of drilling and abrasive water jet induced damage on the performance of carbon fabric/epoxy plates with holes
John Montesano et al.
COMPOSITE STRUCTURES (2017)
An experimental study on abrasive waterjet cutting of CFRP/Ti6Al4V stacks for drilling operations
A. Alberdi et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
Sisal-glass fiber hybrid biocomposite: Optimization of injection molding parameters using Taguchi method for reducing shrinkage
B. Kc et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2016)
Hybridized carbon and flax fiber composites for tailored performance
Jeff Flynn et al.
MATERIALS & DESIGN (2016)
Abrasive Water Jet Machining and Mechanical Behavior of Banyan Tree Saw Dust Powder Loaded Polypropylene Green Composites
Narayanappa Ramesha et al.
POLYMER COMPOSITES (2016)
Comprehensive study on machinability of sustainable and conventional fibre reinforced polymer composites
Sikiru Oluwarotimi Ismail et al.
ENGINEERING SCIENCE AND TECHNOLOGY-AN INTERNATIONAL JOURNAL-JESTECH (2016)
Delamination Characterization and Comparative Assessment of Delamination Control Techniques in Abrasive Water Jet Drilling of CFRP
Kamlesh Phapale et al.
44TH NORTH AMERICAN MANUFACTURING RESEARCH CONFERENCE, NAMRC 44 (2016)
Machinablity of Hybrid Natural Fiber Composite with and without Filler as Reinforcement
S. P. Jani et al.
MATERIALS AND MANUFACTURING PROCESSES (2016)
Development of flax/carbon fibre hybrid composites for enhanced properties
H. N. Dhakal et al.
CARBOHYDRATE POLYMERS (2013)
Characterisation of aggregate notch cavity formation properties on abrasive waterjet cut surfaces
D. J. Thomas
JOURNAL OF MANUFACTURING PROCESSES (2013)
Composite Cutting with Abrasive Water Jet
A. Alberdi et al.
MANUFACTURING ENGINEERING SOCIETY INTERNATIONAL CONFERENCE, (MESIC 2013) (2013)
A review of mechanical drilling for composite laminates
DeFu Liu et al.
COMPOSITE STRUCTURES (2012)
Innovant agromaterials formulated with flax shaves and proteinic binder: Process and characterization
N. El Hajj et al.
COMPOSITES PART B-ENGINEERING (2012)
A review on mechanical behavior of natural fiber based hybrid composites
Srinivas Nunna et al.
JOURNAL OF REINFORCED PLASTICS AND COMPOSITES (2012)
Effect of laminate configuration and feed rate on cutting performance when drilling holes in carbon fibre reinforced plastic composites
Islam Shyha et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2010)
Characteristics of abrasive waterjet cut-edges and the affect on formability and fatigue performance of high strength steels
Daniel J. Thomas
Journal of Manufacturing Processes (2010)
Effect of water absorption on the mechanical properties of hemp fibre reinforced unsaturated polyester composites
H. N. Dhakal et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2007)
Effect of traverse speed on abrasive waterjet machining of Ti-6Al-4V alloy
Ahmet Hascalik et al.
MATERIALS & DESIGN (2007)
The effect of ambient temperature on capillary vascular malformations
DJ McGill et al.
BRITISH JOURNAL OF DERMATOLOGY (2006)
Abrasive water-jet controlled depth milling of Ti6Al4V alloy - an investigation of the role of jet-workpiece traverse speed and abrasive grit size on the characteristics of the milled material
G Fowler et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2005)
Striation formation mechanisms on the jet cutting surface
FL Chen et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)
Comprehensive analysis of delamination in drilling of composite materials with various drill bits
H Hocheng et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)
Machinability of titanium alloy (Ti-6Al-4V) by abrasive waterjets
YW Seo et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2003)
Effects of environmental aging on the mechanical properties of bamboo-glass fiber reinforced polymer matrix hybrid composites
MM Thwe et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2002)
Share Paper
